Oplay mini (non plus) add USB wifi/eth and IPTV

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby Bop4yN » 08 Oct 2015, 08:59

FarVoice, а первый разве не квадратный?
Asus O!Play R1 + AMP r12 + vrt gui
Bop4yN
 
Posts: 13
Joined: 29 Dec 2011, 01:05

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby lymax » 08 Oct 2015, 11:54

А мне кажется, что на фотке явно видно, какой к массе подсоединён - второй справа
Марсы: 2*Emtec Movie Cube S800H (amp_r12 vrtn + amp_r12 noGUI[NFS/Samba/FTP/Trans])
Сатурны: Iconbit XDS73D + eGreat R6S Pro (ампс + скин 3Dgui)
+ eGreat R6S Pro (ампс ногуй) + 2*eGreat R6S для тестов
Сеть/Инет: LAN / WLAN 300Mb / ADSL 16Mb
User avatar
lymax
 
Posts: 245
Joined: 12 Jun 2012, 00:10

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby FarVoice » 08 Oct 2015, 13:30

first - square (in your picture - tx) it's 3.3 V
second - like star (rx) it's ground
and last two - signals.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby droidragon » 09 Oct 2015, 17:29

(cut) overquoting! Forum rules 4.19!

yes thank you! I successfully connected the UART and the log shows up, I tried to manually load the .ko file but it says command not found : insmod (I'm using putty )
droidragon
 
Posts: 16
Joined: 22 Sep 2015, 16:06

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby FarVoice » 09 Oct 2015, 18:03

/sbin/insmod is presented. Show me what you entered.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby droidragon » 10 Oct 2015, 09:51

Image

I tried to add it from kernel/drivers folder as well but same error and to be sure I have to run the command from Monitor mode right?

Sent from my Xperia S using Tapatalk
droidragon
 
Posts: 16
Joined: 22 Sep 2015, 16:06

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby Virtual » 10 Oct 2015, 11:30

1. FAQ
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby FarVoice » 10 Oct 2015, 11:40

why do you entry commands on Realtek monitor?!
wait, when system is up, press ENTER twise and them entry anything.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby droidragon » 10 Oct 2015, 15:57

oops sorry i forgot to update the post anyway i think it successfully detected the wifi adapter/dongle
although nothing happends after it detected the adatper ...whats next ?
Code: Select all
[ExtHddScanUtil.cpp 2148]end time = -1677947179 execute time =  1541 msec
watchdog test pid 98, threshold: 50
insmod /tmp/usbmounts/sda1/8188eu.ko
rtl819xU driver version=v4.1.2_4787.20120803
build time: Nov 25 2013 18:54:26
CHIP TYPE: RTL8188E

usb_endpoint_descriptor(0):
bLength=7
bDescriptorType=5
bEndpointAddress=81
wMaxPacketSize=512
bInterval=0
RT_usb_endpoint_is_bulk_in = 1

usb_endpoint_descriptor(1):
bLength=7
bDescriptorType=5
bEndpointAddress=2
wMaxPacketSize=512
bInterval=0
RT_usb_endpoint_is_bulk_out = 2

usb_endpoint_descriptor(2):
bLength=7
bDescriptorType=5
bEndpointAddress=3
wMaxPacketSize=512
bInterval=0
RT_usb_endpoint_is_bulk_out = 3
nr_endpoint=3, in_num=1, out_num=2

USB_SPEED_HIGH
Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_UNKNOWN_CUT(10)_1T1R_RomVer(0)
RF_Type is 3!!
_ConfigNormalChipOutEP_8188E OutEpQueueSel(0x05), OutEpNumber(2)
EEPROM type is E-FUSE
====> _ReadAdapterInfo8188EU
Boot from EFUSE, Autoload OK !
SCAN END

Key [112] processed.
Key [111] processed.
[DataObject.cpp 1352] SQL ERROR 1 : cannot start a transaction within a transaction
[DataObject.cpp,1426] error : 1 ,cannot start a transaction within a transaction SQL :BEGIN TRANSACTION
SCAN PHASE 2 Init
SCAN PHASE 2 FINISH Audio Id3 Parse
EEPROM ID=0x8129
VID = 0x0BDA, PID = 0x8179
Customer ID: 0x00, SubCustomer ID: 0xCD
Hal_ReadPowerSavingMode88E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
### PS params=>  power_mgnt(1),usbss_enable(0) ###
======= Path 0, Channel 0 =======
Index24G_CCK_Base[0][0] = 0x38
Index24G_BW40_Base[0][0] = 0x35
======= Path 0, Channel 1 =======
Index24G_CCK_Base[0][1] = 0x38
Index24G_BW40_Base[0][1] = 0x35
======= Path 0, Channel 2 =======
Index24G_CCK_Base[0][2] = 0x38
Index24G_BW40_Base[0][2] = 0x35
======= Path 0, Channel 3 =======
Index24G_CCK_Base[0][3] = 0x36
Index24G_BW40_Base[0][3] = 0x33
======= Path 0, Channel 4 =======
Index24G_CCK_Base[0][4] = 0x36
Index24G_BW40_Base[0][4] = 0x33
======= Path 0, Channel 5 =======
Index24G_CCK_Base[0][5] = 0x36
Index24G_BW40_Base[0][5] = 0x33
======= Path 0, Channel 6 =======
Index24G_CCK_Base[0][6] = 0x35
Index24G_BW40_Base[0][6] = 0x32
======= Path 0, Channel 7 =======
Index24G_CCK_Base[0][7] = 0x35
Index24G_BW40_Base[0][7] = 0x32
======= Path 0, Channel 8 =======
Index24G_CCK_Base[0][8] = 0x35
Index24G_BW40_Base[0][8] = 0x32
======= Path 0, Channel 9 =======
Index24G_CCK_Base[0][9] = 0x33
Index24G_BW40_Base[0][9] = 0x30
======= Path 0, Channel 10 =======
Index24G_CCK_Base[0][10] = 0x33
Index24G_BW40_Base[0][10] = 0x30
======= Path 0, Channel 11 =======
Index24G_CCK_Base[0][11] = 0x33
Index24G_BW40_Base[0][11] = 0x30
======= Path 0, Channel 12 =======
Index24G_CCK_Base[0][12] = 0x34
Index24G_BW40_Base[0][12] = 0x31
======= Path 0, Channel 13 =======
Index24G_CCK_Base[0][13] = 0x34
Index24G_BW40_Base[0][13] = 0x31
======= Path 0, Channel 14 =======
Index24G_CCK_Base[0][14] = 0x34
Index24G_BW40_Base[0][14] = 0x31
======= TxCount 0 =======
CCK_24G_Diff[0][0]= 0
OFDM_24G_Diff[0][0]= 2
BW20_24G_Diff[0][0]= 0
BW40_24G_Diff[0][0]= 0
======= TxCount 1 =======
CCK_24G_Diff[0][1]= -2
OFDM_24G_Diff[0][1]= -2
BW20_24G_Diff[0][1]= -2
BW40_24G_Diff[0][1]= -2
======= TxCount 2 =======
CCK_24G_Diff[0][2]= -2
OFDM_24G_Diff[0][2]= -2
BW20_24G_Diff[0][2]= -2
BW40_24G_Diff[0][2]= -2
======= TxCount 3 =======
CCK_24G_Diff[0][3]= -2
OFDM_24G_Diff[0][3]= -2
BW20_24G_Diff[0][3]= -2
BW40_24G_Diff[0][3]= -2
EEPROMRegulatory = 0x2
mlmepriv.ChannelPlan = 0x20
EEPROM Customer ID: 0x 0
EEPROM : AntDivCfg = 1, TRxAntDivType = 1
Board Type: 0x 0
ThermalMeter = 0x1f
<==== _ReadAdapterInfo8188EU in 450 ms
rtw_macaddr_cfg MAC Address  = 40:a5:ef:09:14:83
MAC Address from pnetdev->dev_addr= 40:a5:ef:09:14:83
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
usbcore: registered new driver rtl819xU
~ # [System2ApDaemon.cpp,threadSys2ApExe,156]msg type = 1 ,msg len = 9 ,msg = 77 6C 61 6E 30 20 55 50
Hotplug got one Net Hotplug of "Add" from "wlan0". It may be Realtek's wireless device.
droidragon
 
Posts: 16
Joined: 22 Sep 2015, 16:06

Re: Oplay mini (non plus) add USB wifi/eth and IPTV

Postby FarVoice » 10 Oct 2015, 20:54

if all is ok, just add insmod to autoexec script on plugged USB stick.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

PreviousNext

Return to About Asus O!Play

Who is online

Users browsing this forum: No registered users and 18 guests

cron