Восстановление при самой неудачной прошивке Mars(1073/1283)

о железе плеера и о периферии

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby sanek58 » 18 Jul 2016, 19:32

Большое спасибо за ценную информацию. Будет свободное время обязательно попробую.
IconBIT HDR12L (amp_r12_vrt), IconBIT XDS1003D (inext_hd1_2.20_r1(image alekson)), IconBIT XDS73D (inext_hd1_2.20_r1(image alekson)).
sanek58
 
Posts: 33
Joined: 07 Jul 2016, 22:44

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby sanek58 » 20 Jul 2016, 12:04

Здравствуйте! Согласно Ваших рекомендаций заработал 1 порт USB.
Вопрос: возможно-ли вернутся на оригинальный буткод, что-бы заработал монитор на плеере? Какие варианты?
IconBIT HDR12L (amp_r12_vrt), IconBIT XDS1003D (inext_hd1_2.20_r1(image alekson)), IconBIT XDS73D (inext_hd1_2.20_r1(image alekson)).
sanek58
 
Posts: 33
Joined: 07 Jul 2016, 22:44

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby FarVoice » 20 Jul 2016, 13:00

дело не только в буткоде, но и в GUI. Чтобы заработал дисплейчег, надо вернуть родной буткод и родную прошивку.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8573
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 20 Jul 2016, 17:20

родной бут - чтобы работал в буте (смысла не вижу)
родная прошивка - будет работать от гуя и тооормзить ;) (бут не обязателен!)

PS а че вам такого полезного в дисплейчеке показывало?
PSPS бут не просто так меняли! ибо родной крив.
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6449
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Starling_vit » 28 Aug 2016, 14:42

Доброго времени!
Подскажите, плиз, в такой ситуации. Имеем O!Play HDP-R1. Не загружается. Снял лог с помощью Hyprterminal. По ссылке лог с подключенной флешкой и остановленный через несколько сек после старта, ибо если не сотановить, крутится по кругу и не все сохраняется. Как видится мне есть проблема в железе. Знающие люди, подскажите, куда копнуть? Спасибо.
https://yadi.sk/d/IgFyEe-juYHjh
вот лог PuTty
https://yadi.sk/i/mC61lHqNuYKL2
Asus O!Play HDP-R1 AMP r13
Starling_vit
 
Posts: 2
Joined: 27 Sep 2012, 21:25

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 28 Aug 2016, 16:40

у тебя все признаки "электричесвто кончилось"
аудио и видео проци падают рандомно, даже на стадии инициализации основного процессора.

PS
. MAC стерт
прошивку пробовал через кнопку переставить?
PSPS пробуй менять (чинить) Бп то что в розетку тыкают. (на асусах в 80% в нем проблема)
и да для тестов включать плеер без дисков и usb девайсов.
и да обязательно!
viewtopic.php?f=14&t=1036
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6449
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Starling_vit » 28 Aug 2016, 21:16

Спасибо, попробую другой питатель. Прошивка не обновляется. С подключенной флешкой, зажатым ресетом, втыканием в розетку на экране появляется сообщение о подготовке к обновлению, висит несколько минут, потом все пропадает, изображения нет.
Asus O!Play HDP-R1 AMP r13
Starling_vit
 
Posts: 2
Joined: 27 Sep 2012, 21:25

Re: Восстановление при самой неудачной прошивке Jupiter(1185

Postby vovannovig » 28 Sep 2016, 10:40

Помогите пожалуйста с плеером Egreat R6a
Ко мне попал уже проблемный, играючисть прошивками и бутом каким-то образом залилость с Asus (Почему каким-то образом, да потому что сколько не пробовал удерживать кнопку "восстановления" ни чего не происходило, а тут положил бут и прошивку - включаю и пошла загрузка...)
В общем сейчас имеем кирпич который после включение загружает надпись АСУС и загружает меню, после чего уходит в перезагрузку и так по циклу.

После подключения к консоли видим следующее:
Code: Select all
?hello  world!
5280 52w80a wiaitA[HDMI]: Set I2C Speed = 100 kHz
[HDMI]: Chk_HotPlug() TV is connected.
[HDMI]: Tx Reads EDID from Rx. block=0
[HDMI]: EDID chksum valid!!! chksum=9216 chksum divide 256=0
HDMI DEVICE
PAL logo

REALTEK ROM Monitor, Revision 0001.0202.0023.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      May 11 2010  21:24:37  /0001.0202.0023
MAC address =                   00.06.dc.47.2d.1b
Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision =         0x93 / 0x78
Endianness =                    Little
Flash memory size =             256 MByte
SDRAM size =                    128 MByte
First free SDRAM address =      0x800fca00

Press 'ESC' to Monitor mode

?hello  world!
5280 w5ai2t80 waiA[HDMI]: Set I2C Speed = 100 kHz
[HDMI]: Chk_HotPlug() TV is connected.
[HDMI]: Tx Reads EDID from Rx. block=0
[HDMI]: EDID chksum valid!!! chksum=9216 chksum divide 256=0
HDMI DEVICE
PAL logo

REALTEK ROM Monitor, Revision 0001.0202.0023.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      May 11 2010  21:24:37  /0001.0202.0023
MAC address =                   00.06.dc.47.2d.1b
Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision =         0x93 / 0x78
Endianness =                    Little
Flash memory size =             256 MByte
SDRAM size =                    128 MByte
First free SDRAM address =      0x800fca00

Press 'ESC' to Monitor mode
Linux Kernel:
        FW Image from 0xa2020000, to 0x80100000, size=0x403086
Audio FW:
        FW Image from 0xa2440000, to 0x81b00000, size=0x1c9050
Video FW:
        FW Image from 0xa2620000, to 0x81d80000, size=0x235df8
5280Go 5280Go go 0x80100000 mtdparts=rtk_nand:111232k,76288k(/),61440k(/usr/local/etc),13184k rootfstype=yaffs2 root=31:01
Reset Ethernet Mac.


Address = 0x80100000

Realtek LINUX (DC ALIAS) started...
Venus setting:
        ROSs have 2621440 bytes RAM.
        System CPU has 2 UARTs.
        System CPU uses external timer interrupt.
        Bootloader version: 0001.0202.0023. This version string is of new format.
Error! Unknown SB2_CHIP_INFO. Linux is too old?
        Ethernet Mac address: 00.06.DC.47.2D.1B
        USB1 parameters: 5,4,d
        Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (root@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.01-20051114) #323635 Tue Sep 7 16:49:31 CST 2010
audio addr: 1b00000
CPU revision is: 00019378
Determined physical RAM map:
 memory: 00100000 @ 00000000 (usable)
 memory: 00421000 @ 00100000 (reserved)
 memory: 015df000 @ 00521000 (usable)
 memory: 00500000 @ 01b00000 (reserved)
 memory: 06000000 @ 02000000 (usable)
  show info: max_low_pfn:32768
  show info: min_low_pfn:1313
ZONE: DMA, PFN: 0
ZONE: DVR, PFN: 8192
Built 1 zonelists
Kernel command line: mtdparts=rtk_nand:111232k,76288k(/),61440k(/usr/local/etc),13184k rootfstype=yaffs2 root=31:01 console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 256 (order: 8, 4096 bytes)
Estimate value: CPU frequency 405.02 MHz
Using 27.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 119552k/121724k available (3387k kernel code, 2112k reserved, 577k data, 144k init, 0k highmem)
Warning! Unknown board id.
==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
========== board id: 10202 ==========
[INFO] neptune mode...
boot_param value: a0002800
mode: 1
Se logo mode to PAL
size: 854
color1: 0x808010
color2: 0x8080a1
color3: 0x808042
color4: 0x8080eb
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
se init module major number = 254
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
[user land] CmdBuf virt addr = 80658000/a0658000, phy addr=00658000
   Hello, Realtek TLB Mapper
   AllocBP size: 294912 order: 7
        <<<DVR FREE AREA>>>
        0:      0
        1:      0
        2:      0
        3:      0
        4:      0
        5:      0
        6:      0
        7:      0
        8:      0
        9:      0
        10:     0
        11:     0
        12:     6
                Addr: 87000000, order: 12
                Addr: 86000000, order: 12
                Addr: 85000000, order: 12
                Addr: 84000000, order: 12
                Addr: 83000000, order: 12

[Audio Firmware Version] 329564
[Binary src compiled at] Aug  9 2010 13:37:21


                Addr: 82000000, order: 12
squashfs: version 3.1 (2006/08/19) Phillip Lougher
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
YAFFS Driver Rev:292241 (2010-01-19)
YAFFS Driver is successfully installing.
Initializing Cryptographic API
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize
loop: loaded (max 8 devices)
this  MARS eth RX_OFFSET = 0x0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
MAC address = 0x00.06.DC.47.2D.1B
eth0: RTL-8139C+ at 0xb8016000, 00:06:dc:47:2d:1b, IRQ 2
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
cp_hotplug
PPP BSD Compression module registered
NET: Registered protocol family 24
VenusSFC MTD init
serial flash inaccessible
physmap flash device: 10000000 at fd00000
Realtek NAND Flash Driver Rev:317223 (2010-06-01)
One HY27UF082G2B chip has 1 die(s) on board
nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0
[rtk_nand_scan_bbt] have created bbt B0, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
4 cmdlinepart partitions found on MTD device rtk_nand
RTK: using dynamic nand partition
Creating 4 MTD partitions on "rtk_nand":
0x00000000-0x06ca0000 : "Partition_000"
0x06ca0000-0x0b720000 : "/"
0x0b720000-0x0f320000 : "/usr/local/etc"
0x0f320000-0x10000000 : "Partition_003"
0x00000000-0x10000000 : "disc"
Realtek Nand Flash Driver is successfully installing.
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODE: MARS/JUPITER
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 8
= RX FIFO DEPTH : 8
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
FATAL : I2C 1 pins have been occupied by PCI
Trying to free free IRQ3
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
Realtek Venus Power Management, (c) 2006 Realtek Semiconductor Corp.
cp_open
alloc rings cp->rxdesc_buf =0xa19a5000 , cp->ring_dma=0x19a5000
init_hw
init_hw finished
IP-Config: Complete:
      device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
     host=192.168.0.9, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
RTK rtc can work.
yaffs: restored from checkpoint
VFS: Mounted root (yaffs2 filesystem) readonly.
Mounted devfs on /dev
Freeing prom memory: 0kb freed
Reclaim bootloader memory from 80020000 to 80100000
Freeing unused kernel memory: 144k freed
mount: Mounting none on /tmp failed: No such file or directory
Welcome to Realtek Linux

Please press Enter to activate this console. ------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
[mtdblock_release] Done
[mtdblock_release] Done
[mtdblock_release] Done
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
------flush priority: 10
flush_page_cache: do flush...
Starting INET services....
libata version 1.12 loaded.
sata driver initial...2009/12/30 14:50
mars_init_sata(1255)dev_addr:c00654f0
ata_device_add(4893)probe begin
scsi0 : SATA_DRV
sata dma reset
Running dvdplayer with RootApp
RootApp AVHDD version...
set corepath: /tmp/hdd/volumes/HDD1/
enter 2nd case...
================================================
================================================
root execute DvdPlayer...
================================================
================================================
IN : /tmp/ramfs/smb
downloader 0 starts, 0x101cce58
downloader 1 starts, 0x101cef50
CMD: mkdir -p /tmp/netb/smb
In my system...
CMD: mkdir -p /tmp/smb
In my system...
CMD: ifconfig > /tmp/netb/samba_my_ip
In my system...
Warning!! the Mask is 255.0.0.0.
file system 2, sector 4294966272
mount to /tmp/hdd/volumes/HDD1
file system 4, sector 262144
mount to na
file system 3, sector 262144
mount to /tmp/hdd/root
DB FILENAME = /tmp/ramfs/Setup
[DataObject.cpp 399]DB Develop Version same . Don't be upgrade.
[DataObject.cpp 438]DB Version same . Don't be upgrade.



 m_BookMark_Size=4096 m_Signature_Size=16


GrandMa Rev: 01.21
(User Input)***128MB version...
Pipe Created.
(Internal Event)P   Memory address 0x40000000
ipe Created.
pli initialization...

562 loadThemeSetting resource.cpp
No THEMESET_INI exists
[HDMI]: MARS HDMI is running...
[HDMI]: Disable[I2C0] i2c speed changed to 50 KHz
 HDCP
[HDMI]: Set I2C Speed = 50 kHz and increase i2c pull-low strength.
[HDMI]: Hotplug Change !!! -1 -> 0
Node 0, zone      DMA      0      0      0      1      0      0      0      0      1      1      1      1      0
free pages:  3848
Node 0, zone      DVR      1      0      1      0      0      1      0      1      1      0      0      0      5
free pages: 20901
cached size:  3056
try_to_free_pages: free 0
Node 0, zone      DMA      0      0      0      1      0      0      0      0      1      1      1      1      0
free pages:  3848
Node 0, zone      DVR      1      0      1      0      0      1      0      1      1      0      0      0      5
free pages: 20901
cached size:  3056
+++ ALLOC index: 20480 order: 12
1. start remap DVR zone 87000000(80602000) 4096...
sata1: reset phy again!
sata phy reset
map_done is 0...
+++ ALLOC index: 16384 order: 10
1. start remap DVR zone 86000000(805e2000) 1024...
map_done is 0...
+++ ALLOC index: 18432 order: 11
1. start remap DVR zone 86800000(805f2000) 2048...
map_done is 0...
+++ ALLOC index: 12288 order: 11
1. start remap DVR zone 85000000(805c2000) 2048...
map_done is 0...
+++ ALLOC index: 17408 order: 8
1. start remap DVR zone 86400000(805ea000) 256...
map_done is 0...
+++ ALLOC index: 17664 order: 7
1. start remap DVR zone 86500000(805ec000) 128...
map_done is 0...
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805ed000) 128...
map_done is 0...
--- FREE index: 20480 order: 12
--- FREE index: 16384 order: 10
--- FREE index: 18432 order: 11
--- FREE index: 12288 order: 11
--- FREE index: 17408 order: 8
--- FREE index: 17664 order: 7
--- FREE index: 17792 order: 7
+++ ALLOC index: 16384 order: 8
1. start remap DVR zone 86000000(805e2000) 256...
map_done is 0...
+++ ALLOC index: 16896 order: 9
1. start remap DVR zone 86200000(805e6000) 512...
map_done is 0...
Video DebugMem PVIDEO_RPC_SetDebugMemory Called!+++ ALLOC index: 16640 order: 7
hysical Address 1. start remap DVR zone 86100000(805e4000) 128...
= 0x90ee00
map_done is 0...
+++ ALLOC index: 16768 order: 7
1. start remap DVR zone 86180000(805e5000) 128...
map_done is 0...
+++ ALLOC index: 17408 order: 8
1. start remap DVR zone 86400000(805ea000) 256...
map_done is 0...
[AUDIO WARNING]
 no more memory , do Remote Malloc. Size  0x00186008
+++ ALLOC index: 17920 order: 9
1. start remap DVR zone 86600000(805ee000) 512...
map_done is 0...
-------------------
Audio Version = 329564
Common Version = 322603
Build Date = Aug  9 2010
Build Time = 13:37:21
Note =
-------------------
ClassifyBonding  DD   0x00000002



[Video Firmware Version]   324130
[Video Binary  Built on]   Jul 12 2010 10:28:43
Node 0, zone      DMA      1      2      0      0      1      1      1      1      0      1      1      1      0
free pages:  3829
Node 0, zone      DVR      1      2      1      0      0      1      0      1      2      0      0      1      4
free pages: 19113
cached size:  3079
try_to_free_pages: free 0
Node 0, zone      DMA      1      2      0      0      1      1      1      1      0      1      1      1      0
free pages:  3829
Node 0, zone      DVR      1      2      1      0      0      1      0      1      2      0      0      1      4
free pages: 19113
cached size:  3079
+++ ALLOC index: 12288 order: 12
1. start remap DVR zone 85000000(805c2000) 4096...
map_done is 0...
+++ ALLOC index: 18432 order: 10
1. start remap DVR zone 86800000(805f2000) 1024...
map_done is 0...
+++ ALLOC index: 17664 order: 3
1. start remap DVR zone 86500000(805ec000) 8...
map_done is 0...
Node 0, zone      DMA      0      2      0      0      1      1      1      1      0      1      1      1      0
free pages:  3828
Node 0, zone      DVR      1      2      1      1      1      2      1      2      1      0      1      0      3
free pages: 13985
cached size:  3079
try_to_free_pages: free 0
Node 0, zone      DMA      0      2      0      0      1      1      1      1      0      1      1      1      0
free pages:  3828
Node 0, zone      DVR      1      2      1      1      1      2      1      2      1      0      1      0      3
free pages: 13985
cached size:  3079
+++ ALLOC index: 20480 order: 12
1. start remap DVR zone 87000000(80602000) 4096...
map_done is 0...
Node 0, zone      DMA      0      2      0      0      1      1      1      1      0      1      1      1      0
free pages:  3828
Node 0, zone      DVR      1      2      1      1      1      2      1      2      1      0      1      0      2
free pages:  9889
cached size:  3079

[HDMI]: Hotplug Change !!! 0 -> -----------------------------------------
1 HDMI Cable plu[I2C0] Xfer fail - TXABORT (1/2), Reason=0001
gged in. t=066.1msg->addr  = 3a
89
[HDMI]: Turnmsg->flags = 0001
msg->len   = 1

[HDMI]: Send_Aumsg->buf   = 808caa60
dioMute AP_SETUP-----------------------------------------
_HDMI_MUTE=0 Sel-----------------------------------------
ect=1 PS=0
[HDM[I2C0] Xfer fail - TXABORT (1/2), Reason=0000
I]: AP_SETUP_HDMmsg->addr  = 3a
I_MUTE=1
[HDMI]msg->flags = 0081
: Set HDMI Audiomsg->len   = 1
 Mute(Turn off Amsg->buf   = 808caa60
UDIO)
[HDMI]: S-----------------------------------------
end_AudioMute() try_to_free_pages: free 0
Ok, argp.hdmi_muNode 0, zone      DMA      0      2      0      0      1      1      1      1      0      1      1      1      0
free pages:  3828
te=1
Node 0, zone      DVR      1      2      1      1      1      2      1      2      1      0      1      0      2
free pages:  9889
cached size:  3079
+++ ALLOC index: 8192 order: 12
1. start remap DVR zone 84000000(805a2000) 4096...
map_done is 0...
Error in threshoVBM: configured to SD!
ld value: 0...
[BONDING] ac3_dts_ddp dec= 0x00000000
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key =  0x00000001 (1 : has, 0: no key)
[BONDING] MLP ret= 0x00000000, key= 0x00000000, HBR= 0x00000001, dac= 0x00000000
dac's key =  0x000W0atchDog does n0001 (1 : has, 0: no key)
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key =  0x00000001 (1 : has, 0: no key)
[BONDING] DTSHD ret= 0x00010000, getkey= 0x00000000, HBR =  0x00000001, dac= 0x00000000dac's key =  0x00000001 (1 : has, 0: no key)
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001b to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001c to AUDIO_UNKNOWN_TYPE !!!
dac's key = t receive signal 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001d to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,0,1)
Do you have key?(0 = no!) 0
Bonding option process  0x00000023 to AUDIO_UNKNOW for 2 seconds, N_TYPE !!!
High =  0x00000000, Low =  0x03c1b7fe
The following Format is supported:
MPEG
AC3
LPCM
DTS
WMA
AAC
VORBIS
DV
MLP (TrueHD)
DDP (AC3+, EAC3)
WMA Pro
MP4 LC-AAC
MP4 HE-AAC
RAW AAC
ADPCM
FLAC
A Law PCM
u Law PCM
value: 0
[VIDEO Capability]HighWord  0xffffffff, LowWord  0xffffffff
[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Mars
+++ ALLOC index: 4096 order: 11
1. start remap DVR zone 83000000(80582000) 2048...
map_done is 0...
~~SetVideoStandard 7 1
IN : /tmp/ramfs/usb/livepause
IN : /tmp/ramfs/usb
OUT : /tmp/ramfs/usb/livepause
IN : /tmp/ramfs/usb/rec
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
WARNING[2]:TVE i-underflow @ line 0
WARNING[2]:TVE p-underflow @ line 0
+++ ALLOC index: 19456 order: 9
1. start remap DVR zone 86c00000(805fa000) 512...
map_done is 0...
####### - before ResourceMgr::GetInstance
####### - before bg image
+++ ALLOC index: 19968 order: 9
1. start remap DVR zone 86e00000(805fe000) 512...
map_done is 0...
--- FREE index: 19968 order: 9
####### - load bg image OK!!!
####### - load icon image[0] OK!!!
####### - load icon image[1] OK!!!
####### - load icon image[2] OK!!!
####### - load icon image[3] OK!!!
####### - load icon image[4] OK!!!
####### - load icon image[5] OK!!!
####### - load icon image[6] OK!+++ ALLOC index: 19968 order: 9
!!
1. start remap DVR zone 86e00000(805fe000) 512...
map_done is 0...
--- FREE index: 19968 order: 9
[GuideMenu.cpp:428]:xGetCurMoveDownImg()- nFocusedCtrlIndex: 4
######## ==> [1, 2, 3, 4, 5 6], disappear: 6
####### - Beore draw other
[HDMI]: HDCP_XMT[I2C0] i2c speed changed to 50 KHz
_LINK_H0 T=000.000
[HDMI]: HDCP_XMT_LINK_H1 T=000.000

[HDMI]: Read_EDID ST T=000.000
[HDMI]: Set I2C Speed = 50 kHz
[HDMI]: Tx Reads EDID from Rx. ST T=000.004
[HDMI]: Tx Reads EDID from Rx. block=0
[HDMI]: Tx Reads EDID from Rx. block=1
(Jim:UpdateButtonStatus:325:TVSystemDlg.cpp) HDMI not plugin
In my system...
[HDMI]: Tx Reads EDID from Rx. SP T=000.301
[HDMI]: EDID chksum valid!!! chksum-----------------------------------------
=14848 chksum di[I2C0] Xfer fail - TXABORT (1/2), Reason=0000
vide 256=0
[HDMmsg->addr  = 3a
I]: EDID chksum msg->flags = 0081
valid!!! chksum=msg->len   = 1
14848 chksum divmsg->buf   = 808ca920
ide 256=0
[HDMI-----------------------------------------
]: 24-bit IEEE Registration Identifier (0x000C03) found => HDMI Device
[HDMI]: HDMI_Device=1
[HDMI]: HDMI_Device=1 => HDMI Device
[HDMI]: Check_HDMI_Device, HDMI_Device=1
[HDMI]: EDID chksum valid!!! chksum=14848 chksum divide 256=0
[HDMI]: HDMI Device
[HDMI]: Read_EDID SP T=000.335

[HDMI]: parseHDMI_EDIDInfo
david0611: after Add_ADB_Data, total_adb_length=4
[HDMI]: Content of ADB in EDID:

unsigned char edid_data[4]={
0x04,0x09,0x07,0x07};

[HDMI]: Audio Data Block 09 07 07 Format = 0x1 => Linear PCM (e.g., IEC60958)

[HDMI]: ENUM_AUDIO_EDID_ENABLE(Really send ADB to AUDIO FW.)
[HDMI]: AUDIO firmware version = 329564 Version=2       new RPC Version 2
[HDMI]: call_RPC_TOAGENT_HDMI_OUT_EDID_SVC enable=1 NEW
IN : /tmp/net
Create /tmp/net Ok!!!
DNS IP :  168.  95.   1.   1
 nameserver 168.95.1.1

[ARPC_HDMI_EDID] ena 0x00000001, addr 0x0090ea00
<Audio EDID 1> Version 2 enable
LPCM MaxCH 0x00000002, nBit 0x00000018
SR: 32 44 48
support codec format: 0x00000002
+++ ALLOC index: 19968 order: 9
1. start remap DVR zone 86e00000(805fe000) 512...
map_done is 0...
[HDMI]: GetVidNameByTV  =>  VIDEO_PAL   VIDEO_PROGRESSIVE       => 576p
[HDMI] HDMI_thread(376) call setHDMIAudioVideoFormat()
[HDMI] VID = 0x12       576p WideScreen
[HDMI] check EDID structure !!!!
[HDMI]: Aspect Ratio: 2         Wide_16_9 M1|M0=10
[HDMI]: TVSupportxvYCC = 0
[HDMI]: TVSupportxvYCC = 0, do not send metadata.
[HDMI]: Turn on HDMI................... 1 s_freq=0 c_cnt=0 t=067.327
[HDMI]: TVSupportYCbCr = 3
[HDMI]: This TV supports both YCbCr444 & YCbCr422.
[HDMI]: Disable audio setting by video.
[HDMI]: TVSupportxvYCC = 0, do not send metadata.
[HDMI]: Tell AUDIO firmware, now is HDMI_Video_Forma--- FREE index: 19968 order: 9
t_SD
[HDMI]: Send_Video_Format_To_Audio(0)
[HDMI]: argp.video_type=0
[HDMI]: Clear AVMute
[HDMI]: TURN ON HDMI PHY for Mars
[HDMI]: GetVidNameByTV  =>  VIDEO_PAL   VIDEO_PROGRESSIVE       => 576p
[HDMI]: HDMI Latency does not exist.
[HDMI]: Turn on HDMI AUDIO
[HDMI]: Send_AudioMute AP_SETUP_HDMI_MUTE=1 Select=2 PS=0
[HDMI]: AP_SETUP_HDMI_MUTE=0
[HDMI]: Clear HDMI Audio Mute(Turn on AUDIO)
[HDMI]: Send_AudioMute() Ok, argp.hdmi_mute=0
[HDMI]: SET_HDMI_Frequency ST vid=0x12 HDMI_Freq=1
[HDMI]: call AUDIO_RPC_ToAgent_AOUT_HDMI_Set
[HDMI]: SET_HDMI_Frequency SP vid=0x12 HDMI_Freq=1 hdmi_freq=27
[HDMI]: Setup a wider window of opportunity.
[HDMI]: HDMI_TMDS_SCR1     0x8ca0f0
[HDMI]: HDMISwitchTVSystem SP. t=067.534

[HDMI]: GetVidNameByTV  =>  VIDEO_PAL   VIDEO_PROGRESSIVE       => 576p

0 usb block device found
No Recording Partition Available !!!!!!
No Timeshift Partition Available !!!!!!
In my system...
In my system...
In my system...
sata1: reset phy again!
sata phy reset
Algorithmics/MIPS FPU Emulator v1.5
In my system...
In my system...
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
In my system...
In my system...
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x4, get src = 0x4, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ehci_hcd ehci_hcd: EHCI Host Controller
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected

0 usb block device found
No Recording Partition Available !!!!!hub : individual port power switching
!
No Timeshift hub : individual port over-current protection
Partition Available !!!!!!

0 usb block device found
No Recording Partition Available !!!!!!
No Timeshift Partition Available !!!!!!
[cfyeh] set PPE = 0
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x4, get src = 0x4, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection

0 usb block device found
No Recording Partition Available !!!!!!
No Timeshift Partition Available !!!!!!

0 usb block device found
No Recording Partition Available !!!!!!
No Timeshift Partition Available !!!!!!
usb 1-1: new high speed USB device using ehci_hcd and address 2
(Jim:ScreenSaverAP.cpp:PowerSavingTimerSet:380) Set power saving timer 0 min
In my system...
This is the current time: PowerUP_Done!!!
[AbstractAP.cpp:Init:1875] First boot, start Idle timer
In my system...
scsi2 : SCSI emulation for USB Mass Storage devices

0 usb block device found
No Recording Partition Available !!!!!!
No Timeshift Partition Available !!!!!!

**************Invalid Board**************
System will stop now!!!!!
DG_CloseSurface: Invalid handle!
Delete Network
In my system...
Hotplug got one USB Hotplug of "Add" from port "1".
watchdog test pid 184, threshold: 50
sata1: reset phy extra!
sata phy reset
clear pli setting....
pli initializati***128MB version...
on...
   Memory address 0x40000000
remount RO: ...
chip id: 1283: Mars...
5280 wait5280 wai

>>>>>> Got NAND Flash device!

fw_desc_table_v1->signature=VERONA__
fw_desc_table_v1->version=0x1
fw_desc_table_v1->part_list_len=0xc0
data_buf = 0x10006868
fw_desc_table_v1 = 0x10006868
sizeof(fw_desc_table_v1_t) = 0x20
part_entry = 0x10006888
part_count= 0x4
fw_entry = 0x10006948
FW type, 0x2!
Audio FW found!
Video FW found!
audio_fw_entry->offset = 0x1440000
audio_fw_entry->length = 0x1c9050
audio_fw_entry->target_addr = 0x81b00000
read len = 0x1c9050
video_fw_entry->offset = 0x1620000
video_fw_entry->length = 0x235df8
video_fw_entry->target_addr = 0x81d80000
read len = 0x235df8
[mtdblock_release] Done
[RPC]open for RPC ioctl...
[RPC]start reset...
[RPC]done...

Я так понимаю пошла перезагрузка

 release address: 80029000
 release address: 800f4000
 release address: 800fc000
 release address: 808caa60
 release address: 808caaa0
 release address: 8090ee00
 release address: 83000000
--- FREE index: 4096 order: 11
 release address: 84000000
--- FREE index: 8192 order: 12
 release address: 85000000
--- FREE index: 12288 order: 12
 release address: 86000000
--- FREE index: 16384 order: 8
 release address: 86100000
--- FREE index: 16640 order: 7
 release address: 86180000
--- FREE index: 16768 order: 7
 release address: 86200000
--- FREE index: 16896 order: 9
 release address: 86400000
--- FREE index: 17408 order: 8
 release address: 86500000
--- FREE index: 17664 order: 3
 release address: 86600000
--- FREE index: 17920 order: 9
 release address: 86800000
--- FREE index: 18432 order: 10
 release address: 86c00000
--- FREE index: 19456 order: 9
 release address: 87000000
--- FREE index: 20480 order: 12
termination codeFreeing memory...
: 0
 (null)(0) unkown WEXITSTATUS(status) 1 !!!
try_to_free_pages: free 888
try_to_free_pages: free 617
try_to_free_pages: free 0                                                      done (1505 pages freed)
show_offline_dev_field(1310)dev_addr=c00654f0;
sata1 :device0 not found
sata2 :device1 not found
mars_sata_work_fn
device removed from sata port0
mars_sata_work_fn(1141): no cmd Q
mars_sata_work_fn(1172) hot plug end
device removed from sata port1
mars_sata_work_fn(1141): no cmd Q
mars_sata_work_fn(1172) hot plug end
sata device have removed.
show_scan_dev_field
sata_offline_resume
sata device is scaning...


Пробовал разные способы из первого поста но даже если я получаю "Now Register setting is done!! Please execute 'hyper-terminal' to upload bootcode image to device" то плеер все равно циклически перезагружается и не входит в режим восстановления.
ПОМОГИТЕ ПОЖАЛУЙСТА РЕАНИМИРОВАТЬ ДАННЫЙ АППАРАТ!!!
У меня ОС Windows 10 и адапрер UART CP2102 + большое желание его запустить :D
vovannovig
 
Posts: 1
Joined: 28 Sep 2016, 10:32

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 28 Sep 2016, 15:10

1. у тебя плеер MARS 1073
2. так что входишь в режим восстановления по кн. на корпусе или если она не работает то зажав кн [TAB] в сериальной консоли
и ставишь эту из FAQ, далее все по накатанной. (с обязательным прочтением FAQ и правил.)

PS в будущем можно сменить буткод на более приятный, особо если кн на корпусе перестала работать.
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6449
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby sanchez » 25 Oct 2016, 00:33

Привет всем, знакомый дал Iconbit HDS 5L починить, сказал в один момент не включился. Подключил консоль, пробовал делать erase -e, ersae - m, но шиться не хочет ругается на USB и флешка не светится. Пробовал прошивку на жд кидать, тоже не тянет ее. Монитор консольный не всегда срабытывает, несколько раз приходится перетыкать в розетку чтобы побежал лог. Блоком запитывал от своего XDR100DVBT. Если загрузка прошла как по логу то на тюльпане - заставка Iconbit и так и висит. Лед включения не светится, вентилятор шумит, прошивку через кнопку не кушает.
Code: Select all
?hello  world!
5522880 0wa itwaiA~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A
REALTEK ROM Monitor, Revision 0000.0202.0015.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      Aug  5 2009  22:11:20  /0000.0202.0015MAC address =                   00.11.22.cf.ff.ffProcessor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00Processor ID/revision =         0x93 / 0x78Endianness =                    Little
Flash memory size =             256 MByteSDRAM size =                    128 MByteFirst free SDRAM address =      0x800fd000
Press 'ESC' to Monitor modeSignature(
яяяяяя) error! Entering rescue linux...Rescue kernel in FLASH, total size = 0xec411            seg.1 addr 0xa0a00c09, size = 0xec411            seg.2 addr 0x0, size = 0x0copy rescue0: from a0a00c09 to a1000000, len = ec411decompressing rescue: from a1000000 to a0100000: size = ec411lzma finished decompressing rescue donego 0x80100000 BOOT_TAG=
яяяяяя PAL logoReset Ethernet Mac.
Address = 0x80100000
Realtek LINUX (DC ALIAS) started...
Venus setting:
   ROSs have 2621440 bytes RAM.
   System CPU has 1 UART.
   System CPU uses external timer interrupt.
   Bootloader version: 0000.0202.0015. This version string is of new format.
   The information of this board: Company ID:0x0    CPU ID: 0x12    Board ID: 0x202
   Ethernet Mac address: 00.11.22.cf.ff.ff
   Model Config length=0
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (alan@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.01-20051114) #187 Thu Jul 16 13:45:24 CST 2009

**************************************************************

You didn't specify audio image address, use default instead...

**************************************************************

audio addr: 0

CPU revision is: 00019378

Determined physical RAM map:

 memory: 00100000 @ 00000000 (usable)

 memory: 002a0000 @ 00100000 (reserved)

 memory: 019e0000 @ 003a0000 (usable)

 memory: 00280000 @ 01d80000 (reserved)

 memory: 06000000 @ 02000000 (usable)

  show info: max_low_pfn:32768

  show info: min_low_pfn:928

ZONE: DMA, PFN: 0

ZONE: DVR, PFN: 8192

Built 1 zonelists

Kernel command line: BOOT_TAG=

яяяяяя console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Estimate value: CPU frequency 405.01 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 123648k/125824k available (1912k kernel code, 2112k reserved, 291k data, 404k init, 0k highmem)

Warning! Unknown board id.

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction...  available.

Linux NoNET1.0 for Linux 2.6

SCSI subsystem initialized

usbcore: registered new driver hub

GPIO: register IRQ 3... (Success)

se init module major number = 254

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

   Hello, Realtek TLB Mapper

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x0

NTFS driver 2.1.28 [Flags: R/O].

Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

Mars no support IDE

 ide generic info: ide_generic_init

Mars no support IDE

libata version 1.12 loaded.

sata driver initial...

sata dma reset

sata1: occupy port0, COMRESET ok, sstatus = 113, SCRstatus = 113

sata1: dev 0 ATA, max UDMA/100, 78156288 sectors: lba48

scsi0 : SATA_DRV

sata dma reset

sata2: reset phy again!

sata phy reset

sata2: reset phy again!

sata phy reset

sata2: phy reset timeout!

sata2: no device found (phy stat 00000000)

scsi1 : SATA_DRV

  Vendor: ATA       Model: ST340014A         Rev: 3.10

  Type:   Direct-Access                      ANSI SCSI revision: 05

SCSI device sda: 78156288 512-byte hdwr sectors (40016 MB)

SCSI device sda: drive cache: write back

SCSI device sda: 78156288 512-byte hdwr sectors (40016 MB)

SCSI device sda: drive cache: write back

 /dev/scsi/host0/bus0/target0/lun0: p1

data[0] 0x0 signature[0] 0xbabeface

data[1] 0x0 signature[1] 0xdeadbeef

Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0

VenusSFC MTD init

serial flash inaccessible

physmap flash device: 10000000 at fd00000

Realtek NAND Flash Driver Rev:188640 (2009-05-14)

One HY27UF082G2B chip has 1 die(s) on board

nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

[0] (0, 654, 0, 2047)

[1] (0, 830, 0, 2046)

[2] (0, 1031, 0, 2045)

[3] (0, 1085, 0, 2044)

[4] (0, 1172, 0, 2043)

[5] (0, 1820, 0, 2042)

RTK: using the whole nand as a partitoin

Realtek Nand Flash Driver is successfully installing.

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb_param1] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb_param1] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb_param1] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb_param1] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb_param1] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb_param2] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb_param2] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb_param2] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb_param2] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb_param2] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[cfyeh] set PPE = 0

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb_param1] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb_param1] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb_param1] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb_param1] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb_param1] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb_param2] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb_param2] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb_param2] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb_param2] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb_param2] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

Initializing USB Mass Storage driver...

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

Setting registers , Enable OTG

dwc_otg: version 2.60a 22-NOV-2006

DWC_otg: Shared Tx FIFO mode

i2c /dev entries driver

=========================

= VER : 1.8               

=========================

= PHY : 0               

= MODE: MARS               

DWC_otg: USB RESET

= SPD : 1               

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 8     

= RX FIFO DEPTH : 8     

= FIFO THRESHOLD: 4     

= BUS JAM RECORVER : ON 

= NON STOP WRITE : OFF 

= SP PROTECT : ON 

=========================

FATAL : I2C 1 pins have been occupied by PCI

Trying to free free IRQ3

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 404k freed


init started:  BusyBox v1.1.3 (2009.07.16-05:44+0000) multi-call binary

Starting pid 289, console /dev/console: '/etc/init.d/rcS'
Welcome to Realtek Rescue Linux for PhotoViewer
mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: Unknown error 19
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2

>>>>>> loader start! (Jul 16 2009:13:45:00, version=00.01.01)

Please press Enter to activate this console. пяпппппппппппппппппппппппппппппппппппппппппПпПППППППППППППППППППППППППОООПППООООООООООООООООООООООООООООООООООООООООООООООООООООООООООООООООООООЋОЋООЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЋЊЊЊЋЋЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊЊ ЊЊЊЊЊЊЊЊЊЊЊЊЊ Њ Њ                                                                 
Iconbit XDR100DVBT (inext_tv_1.30_moS_r0)
Iconbit XDS1003D (iNeXT HD1_2.22_r1)
sanchez
 
Posts: 16
Joined: 21 Oct 2016, 23:06

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 1 guest