- Code: Select all
/ # lsmod
Module Size Used by Not tainted
ohci_hcd 25200 0
ehci_hcd 46592 0
sata_mars 26944 0
libata 60976 1 sata_mars
/ #
/ # lsmod
Module Size Used by Not tainted
ohci_hcd 25200 0
ehci_hcd 46592 0
sata_mars 26944 0
libata 60976 1 sata_mars
/ #
~ # dmesg
mars_sata_work_fn
device plug into sata port0
sata dma reset
sata1: occupy port0, COMRESET ok, sstatus = 113, SCRstatus = 113
__mars_sata_phy_reset(925)check taskfile state
sata1 is slow to respond, please be patient
sata1 failed to respond. status:0x80(20 secs)
sata1: HDisk status not ready.
__mars_sata_phy_reset(925)check taskfile state
sata1 is slow to respond, please be patient
sata1 failed to respond. status:0x80(20 secs)
sata1: HDisk status not ready.
__mars_sata_phy_reset(925)check taskfile state
sata1 is slow to respond, please be patient
sata1 failed to respond. status:0x80(20 secs)
sata1:HDisk status not ready! reset port0 phy extra!
sata dma reset
sata1: occupy port0, COMRESET ok, sstatus = 113, SCRstatus = 113
__mars_sata_phy_reset(925)check taskfile state
ata_dev_identify(1477)do ATA identify
sata1: dev 0 cfg 49:0f00 82:746b 83:7f69 84:6163 85:7469 86:3c49 87:6163 88:003f
sata1: dev 0 ATA, max UDMA/100, 156301488 sectors: lba48
Vendor: ATA Model: Hitachi HTS54168 Rev: SB2O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1
data[0] 0x60f29112 signature[0] 0xbabeface
data[1] 0x192fa090 signature[1] 0xdeadbeef
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
mars_sata_work_fn(1172) hot plug end
~ # df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 214.8M 69.0M 145.7M 32% /
/dev/mtdblock/2 4.0M 1.4M 2.6M 35% /usr/local/etc
/dev/rd/0 40.0K 40.0K 0 100% /mnt/rd
/dev/root 214.8M 69.0M 145.7M 32% /usr/local/etc/mos
/dev/loop/0 12.8M 12.8M 0 100% /usr/local/bin
/dev/loop/1 12.4M 12.4M 0 100% /usr/local/bin/Resource
/dev/scsi/host0/bus0/target0/lun0/part1
74.5G 88.1M 74.4G 0% /tmp/usbmounts/sda1
~ # mount
rootfs on / type rootfs (rw)
/dev/root on / type yaffs2 (rw,noatime)
none on /dev type devfs (rw)
none on /proc type proc (rw,nodiratime)
devpts on /dev/pts type devpts (rw)
none on /sys type sysfs (rw)
none on /tmp type ramfs (rw)
/dev/mtdblock/2 on /usr/local/etc type yaffs (rw,noatime)
/dev/rd/0 on /mnt/rd type vfat (rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
/dev/root on /usr/local/etc/mos type yaffs2 (rw,noatime)
/dev/loop/0 on /usr/local/bin type squashfs (ro)
/dev/loop/1 on /usr/local/bin/Resource type squashfs (ro)
/dev/scsi/host0/bus0/target0/lun0/part1 on /tmp/usbmounts/sda1 type ufsd (ro,nodiratime)
~ # fdisk -l
Disk /dev/sda: 80.0 GB, 80026361856 bytes
110 heads, 44 sectors/track, 32293 cylinders
Units = cylinders of 4840 * 512 = 2478080 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 32294 78148608 7 HPFS/NTFS
~ #
# dmesg
mars_sata_work_fn
device plug into sata port0
sata dma reset
sata1: occupy port0, COMRESET ok, sstatus = 113, SCRstatus = 113
__mars_sata_phy_reset(925)check taskfile state
sata1 is slow to respond, please be patient
sata1 failed to respond. status:0x80(20 secs)
sata1: HDisk status not ready.
__mars_sata_phy_reset(925)check taskfile state
sata1 is slow to respond, please be patient
sata1 failed to respond. status:0x80(20 secs)
sata1: HDisk status not ready.
__mars_sata_phy_reset(925)check taskfile state
sata1 is slow to respond, please be patient
sata1 failed to respond. status:0x80(20 secs)
sata1:HDisk status not ready! reset port0 phy extra!
sata dma reset
sata1: occupy port0, COMRESET ok, sstatus = 113, SCRstatus = 113
__mars_sata_phy_reset(925)check taskfile state
ata_dev_identify(1477)do ATA identify
sata1: dev 0 cfg 49:0f00 82:746b 83:7f69 84:6163 85:7469 86:3c49 87:6163 88:003f
sata1: dev 0 ATA, max UDMA/100, 156301488 sectors: lba48
sata1: nodata fail, drv_stat 0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
Vendor: ATA Model: Hitachi HTS54168 Rev: SB2O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0:ata_scsi_translate(840)tf_stat:0xd0
ata_qc_issue(4053)tf_stat:0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_dev_select(1208)BUSY_SKIP!
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_qc_issue_prot(4096)tf_stat:0xd0; dev busy;skip cmd
end_request: I/O error, dev sda, sector 0 , pid(3) comm(events/0)
Buffer I/O error on device sda, logical block 0
ata_scsi_translate(840)tf_stat:0xd0
ata_qc_issue(4053)tf_stat:0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_dev_select(1208)BUSY_SKIP!
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_qc_issue_prot(4096)tf_stat:0xd0; dev busy;skip cmd
end_request: I/O error, dev sda, sector 0 , pid(3) comm(events/0)
Buffer I/O error on device sda, logical block 0
ata_scsi_translate(840)tf_stat:0xd0
ata_qc_issue(4053)tf_stat:0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_dev_select(1208)BUSY_SKIP!
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_qc_issue_prot(4096)tf_stat:0xd0; dev busy;skip cmd
end_request: I/O error, dev sda, sector 0 , pid(3) comm(events/0)
Buffer I/O error on device sda, logical block 0
ldm_validate_partition_table(): Disk read failed.
ata_scsi_translate(840)tf_stat:0xd0
ata_qc_issue(4053)tf_stat:0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_dev_select(1208)BUSY_SKIP!
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_qc_issue_prot(4096)tf_stat:0xd0; dev busy;skip cmd
end_request: I/O error, dev sda, sector 0 , pid(3) comm(events/0)
Buffer I/O error on device sda, logical block 0
ata_scsi_translate(840)tf_stat:0xd0
ata_qc_issue(4053)tf_stat:0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_dev_select(1208)BUSY_SKIP!
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_qc_issue_prot(4096)tf_stat:0xd0; dev busy;skip cmd
end_request: I/O error, dev sda, sector 56 , pid(3) comm(events/0)
Buffer I/O error on device sda, logical block 7
ata_scsi_translate(840)tf_stat:0xd0
ata_qc_issue(4053)tf_stat:0xd0
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_dev_select(1208)BUSY_SKIP!
ATA: abnormal status 0xD0 on port 0xB8012B1C
ata_qc_issue_prot(4096)tf_stat:0xd0; dev busy;skip cmd
end_request: I/O error, dev sda, sector 56 , pid(3) comm(events/0)
Buffer I/O error on device sda, logical block 7
unable to read partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
mars_sata_work_fn(1172) hot plug end
~ # df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 214.8M 69.0M 145.7M 32% /
/dev/mtdblock/2 4.0M 1.4M 2.6M 35% /usr/local/etc
/dev/rd/0 40.0K 40.0K 0 100% /mnt/rd
/dev/root 214.8M 69.0M 145.7M 32% /usr/local/etc/mos
/dev/loop/0 12.8M 12.8M 0 100% /usr/local/bin
/dev/loop/1 12.4M 12.4M 0 100% /usr/local/bin/Resource
~ # mount
rootfs on / type rootfs (rw)
/dev/root on / type yaffs2 (rw,noatime)
none on /dev type devfs (rw)
none on /proc type proc (rw,nodiratime)
devpts on /dev/pts type devpts (rw)
none on /sys type sysfs (rw)
none on /tmp type ramfs (rw)
/dev/mtdblock/2 on /usr/local/etc type yaffs (rw,noatime)
/dev/rd/0 on /mnt/rd type vfat (rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
/dev/root on /usr/local/etc/mos type yaffs2 (rw,noatime)
/dev/loop/0 on /usr/local/bin type squashfs (ro)
/dev/loop/1 on /usr/local/bin/Resource type squashfs (ro)
~ # fdisk -l
~ #
Но после выключения-включения (с пульта) винта нет!!!
Вот лог с прошивкой АМР-р8
~ # dmesg
~ # df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 214.8M 69.0M 145.7M 32% /
/dev/mtdblock/2 4.0M 1.4M 2.6M 35% /usr/local/etc
/dev/rd/0 40.0K 40.0K 0 100% /mnt/rd
/dev/root 214.8M 69.0M 145.7M 32% /usr/local/etc/mos
/dev/loop/0 12.8M 12.8M 0 100% /usr/local/bin
/dev/loop/1 12.4M 12.4M 0 100% /usr/local/bin/Resource
~ # fdisk -l
~ # mount
rootfs on / type rootfs (rw)
/dev/root on / type yaffs2 (rw,noatime)
none on /dev type devfs (rw)
none on /proc type proc (rw,nodiratime)
devpts on /dev/pts type devpts (rw)
none on /sys type sysfs (rw)
none on /tmp type ramfs (rw)
/dev/mtdblock/2 on /usr/local/etc type yaffs (rw,noatime)
/dev/rd/0 on /mnt/rd type vfat (rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
/dev/root on /usr/local/etc/mos type yaffs2 (rw,noatime)
/dev/loop/0 on /usr/local/bin type squashfs (ro)
/dev/loop/1 on /usr/local/bin/Resource type squashfs (ro)
~ # fdisk -l
~ # lsmod
ohci_hcd 21904 0 - Live 0xc00a3000
ehci_hcd 43552 0 - Live 0xc00aa000
venus_ir_new 12992 5 - Live 0xc0096000
sata_mars 22240 0 - Live 0xc0065000
libata 52720 1 sata_mars, Live 0xc006e000
venus_gpio 10032 1 - Live 0xc0058000
~ #
cambit wrote:Ни после вытыкания-втыкания, ни после ребута сейчас не появился...
Я уже думаю, может глюк в шлейфе? какого то напряжения для винта 3,5 дюйма хватает (ибо там два напряжения - 5 и 12) а для ноутбучного нет?
Users browsing this forum: No registered users and 12 guests