Восстановление при самой неудачной прошивке Saturn(1186)

о железе плеера и о периферии

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby _Danila_Master_ » 24 Jan 2017, 13:55

Makc2, а роутер-то зачем в данной операции?!.
LAN-кабель - одним концом в LAN приставки, другим в LAN компа.
Настраиваем статику (TCP/IPv4: 192.168.0.1 / 255.255.255.0) и вперед по инструкции...
RTD1073DD: HDS6L (AMP r13 + noGUI)
RTD1185DD: XDS7GL (iNeXT TV 1.31_moS_r0)
RTD1186DD: XDS73D, Playon!HD3 mini (iNeXT HD1 2.20_r1); XDS8003D - (AMPS_r6_noGUI)
User avatar
_Danila_Master_
 
Posts: 25
Joined: 22 Mar 2015, 02:27
Location: Новороссийск

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Makc2 » 24 Jan 2017, 14:05

Virtual wrote:PS при включении зажимать в гипертерминал Esc. а далее по накатанной буты.

Заливаю по уарту, 10 минут всего. Комп рабочий, не могу отключать сеть.

Не понятно, после ESC он зайдет в Реалтек монитор, а как запустить бут из него? Я думал просто g из d/g/c.
Egreat R160S (R160S-2.5.6.0-by-CSv2.0-DMD-XLCZv4.5)
Iconbit 1003DT2 (inext_hd1_2.22_r1)
Makc2
 
Posts: 24
Joined: 16 Jan 2017, 18:54

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 24 Jan 2017, 14:07

для реалтек монитора придется бинарник превращать в asc а это раза в три больше обьем станет :(

PS
в реалтек мониторе набирай
test

результат должен быть таков:
test | +
Realtek> test
only test 0x18000000
Testing ALL
only test 0x18000000
Testing RAM
Memory test from 0xA00C1000 to 0xB7FFFFFC, 10 loops.
Press Ctrl-C to break
Now running loop 10 -
Test passed


из /d/g/c да просто g но туда попасть можно ток спец файлом....
:lol:
и хуже того если плеер по эксепшн упал сам в /d/g/c то прошивка бута не пройдет!?
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Makc2 » 24 Jan 2017, 14:33

Я вышел из Реалтек монитора и зашел в рекавери конфиг, закачал файл по d
Первый РОМ нажал g
rom1.rtf
(6.12 KiB) Downloaded 170 times


чем должно кончиться?
Egreat R160S (R160S-2.5.6.0-by-CSv2.0-DMD-XLCZv4.5)
Iconbit 1003DT2 (inext_hd1_2.22_r1)
Makc2
 
Posts: 24
Joined: 16 Jan 2017, 18:54

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 24 Jan 2017, 14:44

теперь так же поставь rom2
и плеер должен начать работать на новых бутах...

после чего корми прошивку
viewtopic.php?f=40&t=3707
и уходи из этой темы :mrgreen:

PS только предварительно лог полный нормального включения дай для финишной проверки
и да еще нужно будет разобраться с MAC адресом и маркером гигабитной сети (у тя 100 мбит)/
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Makc2 » 24 Jan 2017, 15:17

Ухожу, ухожу...
Скоро.

Полный лог первого ROM
| +
d/g/c>
d/g/c>defghhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Ymodem:
CCCCCCCCCCCCCCCCCCCCCC
checksum:0x11BC6566
crc32:0x6FCA34B5, len:0x0026CD40
d/g/c>gadvanced recovery tool (compile Virtual)
force NAND
flash type: nand
5
4
3
2
1
Begin:[9590dcad 54 ad]
nf_find_blk
/(3)/(4)/(5)/(6)/(8)/(9)/(a)/(b)/(c)/(d)/(e)/(f)/(10)/(11)/(12)/(13)/(14)/(15)/(
16)/(17)/(18)/(19)/(1a)/(1b)/(1c)/(1d)/(1e)/(1f)/(20)/(21)/(22)/(23)/(24)/(25)/(
26)/(27)/(28)/(29)/(2a)/(2b)/(2c)/(2d)/(2e)/(2f)/(30)/(31)/(32)/(34)/(35)/(36)/(
37)/(38)/(39)/(3a)signature=0x23
.signature=0x23
.signature=0x23
.signature=0x23
.signature=0x79
................................................................................
..............................................................................si
gnature=0x79
................................................................................
..............................................................................si
gnature=0x79
................................................................................
..............................................................................si
gnature=0x79
................................................................................
..............................................................................si
gnature=0x80
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
.......signature=0x80
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
.......signature=0x80
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
.......signature=0x80
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
.......Finish

1

?hello.world
efghhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
NAND
1
c
d
e
2
decrypt24020004
5B7395BC

C

?hello.world
efghhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
5280 wait5280 wait4K&Eunknown PHY: 8403ffff
[HDMI]: Set I2C Speed = 50 kHz
[HDMI]: Chk_HotPlug() TV is not connected.
[HDMI]: Read_EDID abort, HDMI cable plug off.
[HDMI]: TV is not connected.
1080p 60Hz logo
@@@@@@@@@@

REALTEK ROM Monitor, Revision 0000.0402.0042-rom2.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Dec 14 2011 12:34:49 /0000.0402.0042-rom2
MAC address = 00.11.22.33.44.55
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x85
Endianness = Little
Flash memory size = 2 MByte
SDRAM size = 512 MByte
First free SDRAM address = 0x800b2000

Press 'ESC' to Monitor mode
Checksum(0xffffffff) or signature(ÿÿÿÿÿÿÿÿ) error! Entering rescue linux...
@@@ @@@@@@@@update
Rescue kernel in FLASH, total size = 0x153061

seg.1 addr 0xbec52000, size = 0xad000

seg.2 addr 0xbdd10000, size = 0xa6061
copy rescue0: from bec52000 to 81000000, len = ad000
copy rescue1: from bdd10000 to 810ad000, len = a6061
decompressing rescue: from 81000000 to 80100000: size = 153061
lzma finished
decompressing rescue done
go 0x80100000
defer 525i logo
Reset Ethernet Mac.


Address = 0x80100000
Linux version 2.6.34-VENUS (root@localhost.localdomain) (gcc version 4.3.6 20110
218 (prerelease) (GCC) ) #24 PREEMPT Fri Sep 2 16:25:27 CST 2011

Realtek LINUX started...
Venus setting:
ROSs have 4194304 bytes RAM.
System CPU has 1 UART.
System CPU uses internal timer interrupt.
Bootloader version: 0000.0402.0042-rom2. This version string is of new f
ormat.
The information of this board: Company ID:0x0 CPU ID: 0x4 Board ID
: 0x402
Ethernet Mac address: 00.11.22.33.44.55
Model Config length=0
Base year of RTC is 2010.
**************************************************************
You didn't specify audio image address, use default instead...
**************************************************************
audio addr: 0
Config serial console: console=ttyS0,115200n8r
bootconsole [early0] enabled
CPU revision is: 00019385 (MIPS 24Kc)
FPU revision is: 01739300
Determined physical RAM map:
memory: 00020000 @ 00000000 (reserved)
memory: 000e0000 @ 00020000 (ROM data)
memory: 01b00000 @ 00100000 (usable)
memory: 00400000 @ 01c00000 (reserved)
memory: 0e000000 @ 02000000 (usable)
memory: 00100000 @ 10000000 (reserved)
memory: 07f00000 @ 10100000 (usable)
memory: 00100000 @ 18000000 (reserved)
memory: 05b00000 @ 18100000 (usable)
Wasting 8192 bytes for tracking 256 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
DMA 0x00000000 -> 0x00002000
Normal 0x00002000 -> 0x0001dc00
Movable zone start PFN for each node
Node 0: 64512
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x0001dc00
zone DMA size: 2000 realsize: 2000
zone Normal size: dc00 realsize: dc00
zone Movable size: e000 realsize: e000
zonelist: Movable Normal DMA
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 121856
Kernel command line: console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.
0.0.0:::
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0000e00c
Readback ErrCtl register=0000e00c
Memory: 470984k/480256k available (2164k kernel code, 9272k reserved, 641k data,
2020k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:8
Estimated CPU frequency: 756.04 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 502.98 BogoMIPS (lpj=2514944)
Mount-cache hash table entries: 512
devtmpfs: initialized
prom_flashsize = 0x00200000
Flash size is 0x2000000
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS-DMP
Switched to NOHz mode on CPU #0




***************** se init module *********************



se init module major number = 253




***************** md init module *********************



md init module major number = 252
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
init_vdso successfull
rtktlb: Hello, Realtek TLB Mapper...
AllocBP size: 688128 order: 8 offset: 0
<<<DVR FREE AREA>>>
0: 0
1: 0
2: 0
3: 0
4: 0
5: 0
6: 0
7: 0
8: 0
9: 0
10: 0
11: 0
12: 0
13: 7
Addr: 82000000, order: 13
Addr: 84000000, order: 13
Addr: 86000000, order: 13
Addr: 88000000, order: 13
Addr: 8a000000, order: 13
Addr: 8c000000, order: 13
Addr: 8e000000, order: 13
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 919
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Realtek Bulid-In SATA Driver Rev:SATURN (2011-02-24 15:10)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA PackageRealtek NAND Flash Driver Rev:337905 (2010-10-18)
[rtk_nand_init]Bootcode size 0xc00000
[rtk_nand_init]Factory parameter size 0x400000
[rtk_nand_init]Disable NFCP...
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
One H27U4G8F2D chip has 1 die(s) on board
nand part=H27U4G8F2D, id=addc9095, device_size=536870912, chip_size=536870912, n
um_chips=1, page_size=2048, isLastPage=1, eccBits=0
[rtk_nand_scan_bbt] have created bbt B1, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
RTK: using the whole nand as a partitoin
[rtk_nand_init]Ecc bit select 0
Realtek Nand Flash Driver is successfully installing.
VenusSFC MTD init...
NOR flash support list ..
(X) HWSEMA support.
(V) AUTO_HW_POLL support.
(X) 4Bytes mode support.
(V) Max erase size support.
(V) Sfc_delay support.
[venus_sfc_init]FLASH_BASE: 0xbdc00000
[venus_sfc_init]Flash size: 0x2000000
Read id orginal value : 0xc22015c2
--RDID Seq: 0xc2 | 0x20 | 0x15
VenusSFC MTD: MXIC MX25L1605 detected.
SFC_4KB_ERASE
VenusSFC MTD: Enable VenusSFC MD PP callback function.
MD_READ Enable..
MD_WRITE Enable..
[venus_sfc_init]descriptor size 0x2000000
RedBoot partition parsing not available
Venus SFC: using single partition Venus SFC: (for SST/SPANSION/MXIC SPI Flash)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(877) 0xb8013808 = 0x4400a081
#@# cfyeh-debug USBPHY_Register_Setting(879) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(949)
#@#[cfyeh-debug] USBPHY_Register_Setting(951)
#@#[cfyeh-debug] USBPHY_Register_Setting(953)
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x2, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0x9, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x2, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0x9, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ehci ehci: Rtk Dmp EHCI
ehci ehci: new USB bus registered, assigned bus number 1
ehci ehci: irq 2, io mem 0xb8013000
ehci ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(877) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_Register_Setting(879) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(949)
#@#[cfyeh-debug] USBPHY_Register_Setting(951)
#@#[cfyeh-debug] USBPHY_Register_Setting(953)
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x2, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0x9, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x2, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0x9, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ohci ohci: Rtk Dmp OHCI
ohci ohci: new USB bus registered, assigned bus number 2
ohci ohci: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
#@# cfyeh-debug usb3_phy_setting_saturn(27) +++
#@# cfyeh-debug usb3_phy_setting_saturn(216) ---
xhci xhci: Rtk Dmp XHCI
xhci xhci: new USB bus registered, assigned bus number 3
xhci xhci: irq 2, io mem 0xb8020000
#@# cfyeh-debug xhci_irq(1747) 0x000002a0 0x002802a0
#@# cfyeh-debug handle_port_status(1096) 0x000002a0 0x002802a0
#@#[cfyeh-debug] handle_port_status(1124) NOT in U0
usb usb3: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed comp
anion descriptor
ata1: SATA link down (SStatus 0 SControl 300)
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
#@# cfyeh-debug xhci_hub_control(287) hack for usb3 portsc
#@# cfyeh-debug usb3_mac_setting_saturn(221) +++
#@# cfyeh-debug usb3_mac_setting_saturn(242) 16bit
#@# cfyeh-debug usb3_mac_setting_saturn(243) *(unsigned int volatile *)0xb802820
0=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(244) *(unsigned int volatile *)0xb802820
0=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(246) *(unsigned int volatile *)0xb802820
0=0x2400
#@# cfyeh-debug usb3_mac_setting_saturn(257) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(259) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(263) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(264) 0xb8028108 = 0x02400008
#@# cfyeh-debug usb3_mac_setting_saturn(269) 0xb8028108 = 0x21010000
#@# cfyeh-debug usb3_mac_setting_saturn(272) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(273) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(278) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(283) disable usb mulit request
#@# cfyeh-debug usb3_mac_setting_saturn(284) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(286) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(291) GUSB3PIPECTL
#@# cfyeh-debug usb3_mac_setting_saturn(292) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(295) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(298) ---
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
[I2C1] i2c speed changed to 100 KHz
I2C1 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 1
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
Freeing prom memory: 896k freed
Freeing unused kernel memory: 2020k freed
init started: BusyBox v1.11.2 (2011-09-02 16:23:53 CST)
starting pid 405, tty '': '/etc/init.d/rcS'
Welcome to Realtek Rescue Linux for PhotoViewer
BUS_TYPE = (null)
Hotplug: device "ram1" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram2" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram3" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram4" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram5" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram6" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram8" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram9" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram10" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram11" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram12" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram13" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram14" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram7" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram15" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop0" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop6" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop5" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop4" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop3" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop7" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop2" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock1" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock0" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram0" is skipped.
/etc/init.d/rcS: line 49: cannot create /sys/bus/usb/devices/usb1/bEnableHubOnBo
ard_woone: nonexistent directory
mount: mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such devic
e
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such device

Please press Enter to activate this console.
>>>>>> loader start! (Sep 2 2011:16:25:18, version=00.01.01)
[JH] checksignatue(), open /dev/mtdblock0
hub 1-0:1.0: over-current chan
Egreat R160S (R160S-2.5.6.0-by-CSv2.0-DMD-XLCZv4.5)
Iconbit 1003DT2 (inext_hd1_2.22_r1)
Makc2
 
Posts: 24
Joined: 16 Jan 2017, 18:54

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 24 Jan 2017, 15:23

ты зачем rom2 досихпор не прошил?
?hello.world
efghhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
NAND переходит на NAND бут но!
1
c
d
e
2
decrypt24020004
5B7395BC

C (ROM2 иного поколения и чет не срастается)

?hello.world
efghhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
переход на ROM2 (NOR) древний бут
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Makc2 » 24 Jan 2017, 15:55

вот прошил только
| +
d/g/c>
d/g/c>
d/g/c>defghhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Ymodem:
CCCCCCCCC
checksum:0x0C1105F3
crc32:0xB8D0C141, len:0x001B91CC
d/g/c>gadvanced recovery tool (compile Virtual)
force NOR
flash type: serial
5
4
3
2
1
Begin:
flash id [0xc22015]
////////////////................................................................
................................................................................
................................................................................
................................................................................
..................................................linux1: 0xbec63000, 0x9c000
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................/////////////lin
ux2: 0xbdd10000, 0xb2dab
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
............................................................Finish

1


Лог универсальной прошивки
| +
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS-DMP
Switched to NOHz mode on CPU #0




***************** se init module *********************



se init module major number = 253
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
init_vdso successfull
rtktlb: Hello, Realtek TLB Mapper...
AllocBP size: 1277952 order: 9 offset: 8192
<<<DVR FREE AREA>>>
0: 0
1: 0
2: 0
3: 0
4: 0
5: 0
6: 0
7: 0
8: 2
Addr: 90100000, order: 8
Addr: 98100000, order: 8
9: 2
Addr: 90200000, order: 9
Addr: 98200000, order: 9
10: 2
Addr: 90400000, order: 10
Addr: 98400000, order: 10
11: 2
Addr: 90800000, order: 11
Addr: 98800000, order: 11
12: 2
Addr: 91000000, order: 12
Addr: 99000000, order: 12
13: 2
Addr: 82000000, order: 13
Addr: 92000000, order: 13
14: 4
Addr: 84000000, order: 14
Addr: 88000000, order: 14
Addr: 8c000000, order: 14
Addr: 94000000, order: 14
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 919
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
console [ttyS0] enabled, bootconsole disabled16550A
console [ttyS0] enabled, bootconsole disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Realtek Bulid-In SATA Driver Rev:SATURN (2012-07-12 17:10)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA PackageRealtek NAND Flash Driver Rev:337905 (2010-10-18)
(X)Enable interrupt mechanism of NAND driver.
Get parameter from register...
[rtk_nand_init]Bootcode size 0xc00000
[rtk_nand_init]Factory parameter size 0x400000
[rtk_nand_init]Disable NFCP...
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
READ ID:0xad 0xdc 0x90 0x95 0x54 0xad
One H27U4G8F2D chip has 1 die(s) on board
nand part=H27U4G8F2D, id=addc9095, device_size=536870912, chip_size=536870912, n
um_chips=1, page_size=2048, isLastPage=1, eccBits=0
[rtk_nand_scan_bbt] have created bbt B1, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
RTK: using the whole nand as a partitoin
[rtk_nand_init]Ecc bit select 0
Realtek Nand Flash Driver is successfully installing.
VenusSFC MTD init...2012/07/05
***Add segment erase for EON flash ***
NOR flash support list ..
(X) HWSEMA support.
(V) AUTO_HW_POLL support.
(X) 4Bytes mode support.
(V) Max erase size support.
(V) Sfc_delay support.
[venus_sfc_init]FLASH_BASE: 0xbdc00000
[venus_sfc_init]Flash size: 0x2000000
Read id orginal value : 0xc22015c2
--RDID Seq: 0xc2 | 0x20 | 0x15
VenusSFC MTD: MXIC MX25L1605 detected.
SFC_4KB_ERASE
VenusSFC MTD: Supported Erase Size: 64KB 4KB.
VenusSFC MTD: Enable VenusSFC MD PP callback function.
MD_READ Enable..
MD_WRITE Enable..
Freq. reg value 0xb
[venus_sfc_init]descriptor size 0x200000
RedBoot partition parsing not available
Venus SFC: using single partition Venus SFC: (for SST/SPANSION/MXIC SPI Flash)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(844) 0xb8013808 = 0x4400a081
#@# cfyeh-debug USBPHY_Register_Setting(846) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(916)
#@#[cfyeh-debug] USBPHY_Register_Setting(918)
#@#[cfyeh-debug] USBPHY_Register_Setting(920)
#@# cfyeh-debug USBPHY_SetReg_Default_39(272) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ehci ehci: Rtk Dmp EHCI
ehci ehci: new USB bus registered, assigned bus number 1
ehci ehci: irq 2, io mem 0xb8013000
ehci ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(844) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_Register_Setting(846) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(916)
#@#[cfyeh-debug] USBPHY_Register_Setting(918)
#@#[cfyeh-debug] USBPHY_Register_Setting(920)
#@# cfyeh-debug USBPHY_SetReg_Default_39(272) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ohci ohci: Rtk Dmp OHCI
ohci ohci: new USB bus registered, assigned bus number 2
ohci ohci: irq 2, io mem 0xb8013400
ata1: SATA link down (SStatus 0 SControl 300)
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
#@# cfyeh-debug usb3_phy_setting_saturn(26) +++
#@# cfyeh-debug usb3_phy_setting_saturn(215) ---
xhci xhci: Rtk Dmp XHCI
xhci xhci: new USB bus registered, assigned bus number 3
xhci xhci: irq 2, io mem 0xb8020000
#@# cfyeh-debug xhci_irq(2239) 0x000002a0 0x002802a0
#@# cfyeh-debug handle_port_status(1264) 0x000002a0 0x002802a0
#@#[cfyeh-debug] handle_port_status(1341) NOT in U0
#@# cfyeh-debug handle_port_status(1361) 0x000002a0 0x002802a0
usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting
0 ep 129: using minimum values
#######[cfyeh-debug] hub_events(3725) usb_plug_status 1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
#@# cfyeh-debug xhci_hub_control(467) hack for usb3 portsc
#@# cfyeh-debug usb3_mac_setting_saturn(220) +++
#@# cfyeh-debug usb3_mac_setting_saturn(241) 16bit
#@# cfyeh-debug usb3_mac_setting_saturn(242) *(unsigned int volatile *)0xb802820
0=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(243) *(unsigned int volatile *)0xb802820
0=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(245) *(unsigned int volatile *)0xb802820
0=0x2400
#@# cfyeh-debug usb3_mac_setting_saturn(256) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(258) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(262) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(263) 0xb8028108 = 0x02400008
#@# cfyeh-debug usb3_mac_setting_saturn(268) 0xb8028108 = 0x21010000
#@# cfyeh-debug usb3_mac_setting_saturn(271) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(272) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(277) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(282) disable usb mulit request
#@# cfyeh-debug usb3_mac_setting_saturn(283) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(285) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(290) GUSB3PIPECTL
#@# cfyeh-debug usb3_mac_setting_saturn(291) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(294) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(297) ---
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered. (0x5)
i2c /dev entries driver
[I2C0] mode=i2c, phy=0, port=-1
[I2C] open I2C0 successed, reference cnt=1
I2C0 Bus Status Check.... OK
=========================
= VER : 2.2
=========================
= PHY : 0
= PORT: 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= SDA GPIO : MISC_GPIO62
= SCL GPIO : MISC_GPIO61
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
usb 1-2: new high speed USB device using ehci and address 2
[I2C1] mode=i2c, phy=1, port=-1
[I2C] open I2C1 successed, reference cnt=1
I2C1 Bus Status Check.... OK
=========================
= VER : 2.2
=========================
= PHY : 1
= PORT: 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= SDA GPIO : MISC_GPIO64
= SCL GPIO : MISC_GPIO63
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
<<<<< Enable memory protector >>>>>
avcpu: audio & video cpu driver for Realtek Media Processors
Freeing prom memory: 768k freed
Freeing unused kernel memory: 2256k freed
init started: BusyBox v1.11.2 (2012-08-28 18:33:07 CST)
starting pid 409, tty '': '/etc/init.d/rcS'
Welcome to Realtek Rescue Linux for PhotoViewer
/etc/init.d/rcS: line 47: cannot create /sys/bus/usb/devices/usb1/bEnableHubOnBo
ard_woone: nonexistent directory
mount: mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such devic
e
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such device

Please press Enter to activate this console.
>>>>>> loader start! (Aug 28 2012:18:34:46, version=00.01.01)
[JH] checksignatue(), open(/dev/mtdblock0) nand_boot_size(0xc00000) factory_size
(0x400000)
no IMG_XXXX signature found
fw_pkg_name:
fw_pkg_name++++++: install.img
scsi1 : usb-storage 1-2:1.0
#######[cfyeh-debug] hub_events(3729) usb_plug_status 0
#######[cfyeh-debug] usb_stor_scan_thread(840) usb_plug_status 1
#@#[cfyeh-debug] usb_stor_scan_thread(850) waiting 5 sec for device to settle be
fore scanning
BUS_TYPE = (null)
Hotplug: device "ram0" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram1" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram4" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram3" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram2" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram5" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram6" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram8" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram7" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram10" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram12" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram13" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram14" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram9" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram11" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop0" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop2" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram15" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop3" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop6" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop5" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop7" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock0" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop4" is skipped.
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
#@#[cfyeh-debug] qtd_copy_status(229) QTD_CERR(token) 0x3 CERR nonzero + halt --
> stall
#######[cfyeh-debug] usb_stor_scan_thread(869) usb_plug_status 2
scsi 1:0:0:0: Direct-Access Generic USB Flash Disk 8.07 PQ: 0 ANSI: 2
#@#[cfyeh-debug] sd_probe(2311) sd_flag 1
#@#[cfyeh-debug] sd_probe(2377) sd_flag 0
#@#[cfyeh-debug] sd_probe_async(2216) sd_flag 1
#@#[cfyeh-debug] sd_revalidate_disk(2091) sd_flag 2
#######[cfyeh-debug] usb_stor_scan_thread(872) usb_plug_status 1
#######[cfyeh-debug] usb_stor_scan_thread(879) usb_plug_status 0
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
sd 1:0:0:0: [sda] 7888896 512-byte logical blocks: (4.03 GB/3.76 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
#@#[cfyeh-debug] sd_revalidate_disk(2150) sd_flag 1
#@#[cfyeh-debug] sd_revalidate_disk(2091) sd_flag 2
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
sd 1:0:0:0: [sda] Assuming drive cache: write through
#@#[cfyeh-debug] sd_revalidate_disk(2150) sd_flag 1
sda: sda1
data[0] 0x0 signature[0] 0xbabeface
data[1] 0x0 signature[1] 0xdeadbeef
#@#[cfyeh-debug] sd_revalidate_disk(2091) sd_flag 2
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
BUS_TYPE = usb
Hotplug: mount -t vfat -o ro,shortname=winnt,iocharset=utf8,umask=0 /dev/sda1 /v
ar/lock/hotplug/mount_tmp/.sda1 ret: 0
Hotplug: Mount "sda1" successfully.
sd 1:0:0:0: [sda] Assuming drive cache: write through
#@#[cfyeh-debug] sd_revalidate_disk(2150) sd_flag 1
sd 1:0:0:0: [sda] Attached SCSI removable disk
#@#[cfyeh-debug] sd_probe_async(2278) sd_flag 0
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
build_imgfile_list: namelist[n]->d_name: .
pattern_byte=i
object_byte=.
pattern_byte+=i
object_byte+=.
build_imgfile_list: namelist[n]->d_name: ..
pattern_byte=i
object_byte=.
pattern_byte+=i
object_byte+=.
build_imgfile_list: namelist[n]->d_name: Egreat
pattern_byte=i
object_byte=E
pattern_byte+=i
object_byte+=E
build_imgfile_list: namelist[n]->d_name: HyperTerminal
pattern_byte=i
object_byte=H
pattern_byte+=i
object_byte+=H
build_imgfile_list: namelist[n]->d_name: R200S_3.0.5.6++flash
pattern_byte=i
object_byte=R
pattern_byte+=i
object_byte+=R
build_imgfile_list: namelist[n]->d_name: USB flash
pattern_byte=i
object_byte=U
pattern_byte+=i
object_byte+=U
build_imgfile_list: namelist[n]->d_name: boot
pattern_byte=i
object_byte=b
pattern_byte+=i
object_byte+=b
build_imgfile_list: namelist[n]->d_name: install.img
pattern_byte=i
object_byte=i
pattern_byte=n
object_byte=n
pattern_byte=s
object_byte=s
pattern_byte=t
object_byte=t
pattern_byte=a
object_byte=a
pattern_byte=l
object_byte=l
pattern_byte=l
object_byte=l
pattern_byte=.
object_byte=.
pattern_byte=i
object_byte=i
pattern_byte=m
object_byte=m
pattern_byte=g
object_byte=g
pattern_byte+=
object_byte+=
(pattern_byte ==pattern_comparing11
build_imgfile_list: namelist[n]->d_name: install.img.install_a.log
pattern_byte=i
object_byte=i
pattern_byte=n
object_byte=n
pattern_byte=s
object_byte=s
pattern_byte=t
object_byte=t
pattern_byte=a
object_byte=a
pattern_byte=l
object_byte=l
pattern_byte=l
object_byte=l
pattern_byte=.
object_byte=.
pattern_byte=i
object_byte=i
pattern_byte=m
object_byte=m
pattern_byte=g
object_byte=g
pattern_byte+=
object_byte+=.
(pattern_byte ==pattern_comparing11
build_imgfile_list: namelist[n]->d_name: rescu
pattern_byte=i
object_byte=r
pattern_byte+=i
object_byte+=r
build_imgfile_list: namelist[n]->d_name: руководство.docx
pattern_byte=i
object_byte=Ñ
pattern_byte+=i
object_byte+=Ñ
totallistcount: 2
img_list[first_big_useful_index].filename: /mnt/usbmounts/sda1/install.img
tar: UI: not found in archive
command: tar -xOf /mnt/usbmounts/sda1/install.img install_a > /install_a
x_io: module_layout: kernel tainted.
Disabling lock debugging due to kernel taint
MOS: install boot
Kernel bug detected[#1]:
Cpu 0
$ 0 : 00000000 805e0000 00000001 00000000
$ 4 : 00000000 9d919b68 00000002 00000008
$ 8 : 001c65a8 00000000 00000000 001c65a8
$12 : 00000008 00000000 00000000 00000000
$16 : 00000000 9d8169b0 9d9f1944 9d059a00
$20 : 00000001 9d003d48 00000678 9d9f197c
$24 : 00000000 802464c8
$28 : 9d918000 9d919b48 00000000 8020ca0c
Hi : 00000000
Lo : 001c25a8
epc : 8020ca34 fat_get_block+0x350/0x400
Tainted: GF
ra : 8020ca0c fat_get_block+0x328/0x400
Status: 10007c03 KERNEL EXL IE
Cause : 58808034
PrId : 00019385 (MIPS 24Kc)
Modules linked in: x_io(F)
Process dmesg (pid: 485, threadinfo=9d918000, task=9d964718, tls=00000000)
Stack : 9d9f197c 801cf1a0 00000000 00000000 9d919b70 9d919b68 00000001 8081c660
00000002 00000000 001c65a8 00000000 9d037000 00000000 8081c660 fffffff4
00000200 00000200 9d919bc4 00000000 00000000 8081c660 00000e57 801d1d3c
9d9f1a28 8081c660 9d9f1a28 8081c660 9d003d48 00000001 9d003d48 9d9f1a28
00000000 000000d0 00000000 fffff3a9 fffffe00 9d003d48 00000200 00000678
...
Call Trace:
[<8020ca34>] fat_get_block+0x350/0x400
[<801d1d3c>] __block_prepare_write+0x1f4/0x524
[<801d2300>] block_write_begin+0xa4/0x14c
[<801d26f4>] cont_write_begin+0x34c/0x3c0
[<8020cc50>] fat_write_begin+0x4c/0x58
[<80173568>] generic_file_buffered_write+0xf8/0x2a4
[<80175f1c>] __generic_file_aio_write+0x4d0/0x52c
[<80175ffc>] generic_file_aio_write+0x84/0xfc
[<801a57b0>] do_sync_write+0xb8/0x120
[<801a6470>] vfs_write+0xac/0x170
[<801a6628>] sys_write+0x58/0xa0
[<80102764>] stack_done+0x20/0x3c


Code: 8fa20020 02821026 0002102b <00028036> 2404ffff c2a20000 7c823184 e2a2
0000 10400022
Segmentation fault

starting pid 430, tty '': '-/bin/sh'


BusyBox v1.18.5 (2012-02-04 12:06:08 MSK) built-in shell (ash)
Enter 'help' for a list of built-in commands.

-/bin/sh: can't access tty; job control turned off
/ # test
/ #


Тест
| +
?hello.world
efghhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
cde
profile->manufacturer_id (first 4B):9590DCAD
profile->data_per_page:800
profile->page_per_block:40

blk 79 starts from page 1C0
24020004
5B7395BC

C

?hello.world
efghhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
klmnopqrstu5280 wait5280 wait4K&factory error
new default_tv_system=NTSC
Eunknown PHY: 8403ffff

REALTEK ROM Monitor, Revision 0000.0402.0060.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Oct 22 2014 10:04:00 /0000.0402.0060
MAC address = 00.11.22.33.44.55
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x85
Endianness = Little
Flash memory size = 2 MByte
SDRAM size = 512 MByte
First free SDRAM address = 0x800c6000

Press 'ESC' to Monitor mode
[HDMI]: Set I2C Speed = 50 kHz
[HDMI]: Chk_HotPlug() TV is not connected.
[HDMI]: Read_EDID abort, HDMI cable plug off.
[HDMI]: TV is not connected.
1st for NTSC
NTSC logo
Realtek>
Realtek>
Realtek> help

Available commands :

. . (repeat last command line)
; ; (command separator)
+ + <repeat count> ;
compare compare <address1> <address2> <size>
continue continue
copy copy [-f] <src> <dst> <size>
dump dump [-m][-8|-16|-32] <address> [<size>]
erase erase -e|-m| <address> <size>
factory factory [-r|-w|-sha1] <address> <size> or factory -c
fill fill [-8|-16|-32] <address> <size> <data>
fread fread tftp://<ipaddr>/<filename> <address>
fwrite fwrite tftp://<ipaddr>/<filename> <address> <size>
go go [?|.|<address> [<args>]]
help help [<command>]
info info [boot|board|cpu|sysctrl|memory|uart|all|pll]
load load [-r]
([tftp:][//<ipaddr>][/<filename>]) |
([asc:] [//(tty0|tty1)])
lzma lzma <src_address> <dst_address> <size>
ping ping ipaddr [<datagramsize>]
port port [-a] [-8|-16|-32] <address> [<value>]
reset reset
saveenv saveenv
setenv setenv [<variable> [<value>]]
stty stty [-tty<0|1>] [-b|-u|[-p][<baudrate>][n|o|e][7|8][1|2][hw|none]]
tar tar <name> <src_address> <size>
test test [-l] | [-m] [ <module> [ <module arguments> ] ]

Realtek> test
only test 0x18000000
Testing ALL
only test 0x18000000
Testing RAM
Memory test from 0xA00C6000 to 0xB7FFFFFC, 10 loops.
Press Ctrl-C to break
Now running loop 10 -
Test passed

Realtek>


пойду искать где МАК адрес и 100 МБ менять :shock: ужос
если дадите ссылочку буду очень рад
Egreat R160S (R160S-2.5.6.0-by-CSv2.0-DMD-XLCZv4.5)
Iconbit 1003DT2 (inext_hd1_2.22_r1)
Makc2
 
Posts: 24
Joined: 16 Jan 2017, 18:54

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 24 Jan 2017, 16:29

покажи просто лог включения после прошивки rom2
ибо по логу ты в режиме NOR из него прошивку не поставить!

и при прошивке универсального бута (а это не нужно ибо ты ранее его по шлангу поставил ) очень много ругани на USB флешку! вероятно битые данные.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Makc2 » 24 Jan 2017, 16:40

вот просто после включения

| +
?hello.world
efghhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
cde
profile->manufacturer_id (first 4B):9590DCAD
profile->data_per_page:800
profile->page_per_block:40

blk 79 starts from page 1C0
24020004
5B7395BC

C

?hello.world
efghhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
Jump!
klmnopqrstu5280 wait5280 wait4K&factory error
new default_tv_system=NTSC
Eunknown PHY: 8403ffff

REALTEK ROM Monitor, Revision 0000.0402.0060.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Oct 22 2014 10:04:00 /0000.0402.0060
MAC address = 00.11.22.33.44.55
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x85
Endianness = Little
Flash memory size = 2 MByte
SDRAM size = 512 MByte
First free SDRAM address = 0x800c6000

Press 'ESC' to Monitor mode
Can not find signature string, "SCIT____"! Entering rescue linux...
[HDMI]: Set I2C Speed = 50 kHz
[HDMI]: Chk_HotPlug() TV is not connected.
[HDMI]: Read_EDID abort, HDMI cable plug off.
[HDMI]: TV is not connected.
1st for NTSC
NTSC logo
Rescue kernel in FLASH, total size = 0x14edab
seg.1 addr 0xbec63000, size = 0x9c000
seg.2 addr 0xbdd10000, size = 0xb2dab
copy rescue0: from bec63000 to 81000000, len = 9c000
copy rescue1: from bdd10000 to 8109c000, len = b2dab
decompressing rescue: from 81000000 to 80100000: size = 14edab
lzma finished
decompressing rescue done
go 0x80100000
Reset Ethernet Mac.


Address = 0x80100000
Linux version 2.6.34-VENUS (wilmawu@dtv_server00) (gcc version 4.3.6 20110218 (p
rerelease) (GCC) ) #4 PREEMPT Tue Aug 28 18:34:56 CST 2012

Realtek LINUX started...
Venus setting:
ROSs have 4194304 bytes RAM.
System CPU has 1 UART.
System CPU uses internal timer interrupt.
Bootloader version: 0000.0402.0060. This version string is of new format
.
The information of this board: Company ID:0x0 CPU ID: 0x4 Board ID
: 0x402
Ethernet Mac address: 00.11.22.33.44.55
Model Config length=0
Base year of RTC is 2010.
**************************************************************
You didn't specify audio image address, use default instead...
**************************************************************
audio addr: 0
Config serial console: console=ttyS0,115200n8r
bootconsole [early0] enabled
CPU revision is: 00019385 (MIPS 24Kc)
FPU revision is: 01739300
Determined physical RAM map:
memory: 00040000 @ 00000000 (reserved)
memory: 000c0000 @ 00040000 (ROM data)
memory: 01b00000 @ 00100000 (usable)
memory: 00400000 @ 01c00000 (reserved)
memory: 0e000000 @ 02000000 (usable)
memory: 00100000 @ 10000000 (reserved)
memory: 07f00000 @ 10100000 (usable)
memory: 00100000 @ 18000000 (reserved)
memory: 05b00000 @ 18100000 (usable)
Wasting 8192 bytes for tracking 256 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
DMA 0x00000000 -> 0x00002000
Normal 0x00002000 -> 0x0001dc00
Movable zone start PFN for each node
Node 0: 23552
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x0001dc00
zone DMA size: 2000 realsize: 2000
zone Normal size: 3c00 realsize: 3c00
zone Movable size: 18000 realsize: 18000
zonelist: Movable Normal DMA
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 121856
Kernel command line: console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.
0.0.0:::
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00026000
Readback ErrCtl register=00026000
Memory: 470568k/480256k available (2077k kernel code, 9688k reserved, 642k data,
2256k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:8
Estimated CPU frequency: 796.54 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208)
Mount-cache hash table entries: 512
devtmpfs: initialized
UART_NR=2
UART_NR=2
prom_flashsize = 0x00200000
Flash size is 0x2000000
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS-DMP
Switched to NOHz mode on CPU #0




***************** se init module *********************



se init module major number = 253
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
init_vdso successfull
rtktlb: Hello, Realtek TLB Mapper...
AllocBP size: 1277952 order: 9 offset: 8192
<<<DVR FREE AREA>>>
0: 0
1: 0
2: 0
3: 0
4: 0
5: 0
6: 0
7: 0
8: 2
Addr: 90100000, order: 8
Addr: 98100000, order: 8
9: 2
Addr: 90200000, order: 9
Addr: 98200000, order: 9
10: 2
Addr: 90400000, order: 10
Addr: 98400000, order: 10
11: 2
Addr: 90800000, order: 11
Addr: 98800000, order: 11
12: 2
Addr: 91000000, order: 12
Addr: 99000000, order: 12
13: 2
Addr: 82000000, order: 13
Addr: 92000000, order: 13
14: 4
Addr: 84000000, order: 14
Addr: 88000000, order: 14
Addr: 8c000000, order: 14
Addr: 94000000, order: 14
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 919
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Realtek Bulid-In SATA Driver Rev:SATURN (2012-07-12 17:10)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA PackageRealtek NAND Flash Driver Rev:337905 (2010-10-18)
(X)Enable interrupt mechanism of NAND driver.
Get parameter from register...
[rtk_nand_init]Bootcode size 0xc00000
[rtk_nand_init]Factory parameter size 0x400000
[rtk_nand_init]Disable NFCP...
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
READ ID:0xad 0xdc 0x90 0x95 0x54 0xad
One H27U4G8F2D chip has 1 die(s) on board
nand part=H27U4G8F2D, id=addc9095, device_size=536870912, chip_size=536870912, n
um_chips=1, page_size=2048, isLastPage=1, eccBits=0
[rtk_nand_scan_bbt] have created bbt B1, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
RTK: using the whole nand as a partitoin
[rtk_nand_init]Ecc bit select 0
Realtek Nand Flash Driver is successfully installing.
VenusSFC MTD init...2012/07/05
***Add segment erase for EON flash ***
NOR flash support list ..
(X) HWSEMA support.
(V) AUTO_HW_POLL support.
(X) 4Bytes mode support.
(V) Max erase size support.
(V) Sfc_delay support.
[venus_sfc_init]FLASH_BASE: 0xbdc00000
[venus_sfc_init]Flash size: 0x2000000
Read id orginal value : 0xc22015c2
--RDID Seq: 0xc2 | 0x20 | 0x15
VenusSFC MTD: MXIC MX25L1605 detected.
SFC_4KB_ERASE
VenusSFC MTD: Supported Erase Size: 64KB 4KB.
VenusSFC MTD: Enable VenusSFC MD PP callback function.
MD_READ Enable..
MD_WRITE Enable..
Freq. reg value 0xb
[venus_sfc_init]descriptor size 0x200000
RedBoot partition parsing not available
Venus SFC: using single partition Venus SFC: (for SST/SPANSION/MXIC SPI Flash)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(844) 0xb8013808 = 0x4400a081
#@# cfyeh-debug USBPHY_Register_Setting(846) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(916)
#@#[cfyeh-debug] USBPHY_Register_Setting(918)
#@#[cfyeh-debug] USBPHY_Register_Setting(920)
#@# cfyeh-debug USBPHY_SetReg_Default_39(272) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ehci ehci: Rtk Dmp EHCI
ehci ehci: new USB bus registered, assigned bus number 1
ehci ehci: irq 2, io mem 0xb8013000
ehci ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(844) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_Register_Setting(846) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(203) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(916)
#@#[cfyeh-debug] USBPHY_Register_Setting(918)
#@#[cfyeh-debug] USBPHY_Register_Setting(920)
#@# cfyeh-debug USBPHY_SetReg_Default_39(272) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ohci ohci: Rtk Dmp OHCI
ohci ohci: new USB bus registered, assigned bus number 2
ohci ohci: irq 2, io mem 0xb8013400
ata1: SATA link down (SStatus 0 SControl 300)
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
#@# cfyeh-debug usb3_phy_setting_saturn(26) +++
#@# cfyeh-debug usb3_phy_setting_saturn(215) ---
xhci xhci: Rtk Dmp XHCI
xhci xhci: new USB bus registered, assigned bus number 3
xhci xhci: irq 2, io mem 0xb8020000
#@# cfyeh-debug xhci_irq(2239) 0x000002a0 0x002802a0
#@# cfyeh-debug handle_port_status(1264) 0x000002a0 0x002802a0
#@#[cfyeh-debug] handle_port_status(1341) NOT in U0
#@# cfyeh-debug handle_port_status(1361) 0x000002a0 0x002802a0
usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting
0 ep 129: using minimum values
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
#@# cfyeh-debug xhci_hub_control(467) hack for usb3 portsc
#@# cfyeh-debug usb3_mac_setting_saturn(220) +++
#@# cfyeh-debug usb3_mac_setting_saturn(241) 16bit
#@# cfyeh-debug usb3_mac_setting_saturn(242) *(unsigned int volatile *)0xb802820
0=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(243) *(unsigned int volatile *)0xb802820
0=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(245) *(unsigned int volatile *)0xb802820
0=0x2400
#@# cfyeh-debug usb3_mac_setting_saturn(256) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(258) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(262) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(263) 0xb8028108 = 0x02400008
#@# cfyeh-debug usb3_mac_setting_saturn(268) 0xb8028108 = 0x21010000
#@# cfyeh-debug usb3_mac_setting_saturn(271) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(272) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(277) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(282) disable usb mulit request
#@# cfyeh-debug usb3_mac_setting_saturn(283) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(285) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(290) GUSB3PIPECTL
#@# cfyeh-debug usb3_mac_setting_saturn(291) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(294) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(297) ---
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered. (0x5)
i2c /dev entries driver
[I2C0] mode=i2c, phy=0, port=-1
[I2C] open I2C0 successed, reference cnt=1
I2C0 Bus Status Check.... OK
=========================
= VER : 2.2
=========================
= PHY : 0
= PORT: 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= SDA GPIO : MISC_GPIO62
= SCL GPIO : MISC_GPIO61
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
[I2C1] mode=i2c, phy=1, port=-1
[I2C] open I2C1 successed, reference cnt=1
I2C1 Bus Status Check.... OK
=========================
= VER : 2.2
=========================
= PHY : 1
= PORT: 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= SDA GPIO : MISC_GPIO64
= SCL GPIO : MISC_GPIO63
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
<<<<< Enable memory protector >>>>>
avcpu: audio & video cpu driver for Realtek Media Processors
Freeing prom memory: 768k freed
Freeing unused kernel memory: 2256k freed
init started: BusyBox v1.11.2 (2012-08-28 18:33:07 CST)
starting pid 409, tty '': '/etc/init.d/rcS'
Welcome to Realtek Rescue Linux for PhotoViewer
/etc/init.d/rcS: line 47: cannot create /sys/bus/usb/devices/usb1/bEnableHubOnBo
ard_woone: nonexistent directory
mount: mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such devic
e
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such device

Please press Enter to activate this console.
>>>>>> loader start! (Aug 28 2012:18:34:46, version=00.01.01)
[JH] checksignatue(), open(/dev/mtdblock0) nand_boot_size(0xc00000) factory_size
(0x400000)
no IMG_XXXX signature found
fw_pkg_name:
fw_pkg_name++++++: install.img
BUS_TYPE = (null)
Hotplug: device "ram5" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram4" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram3" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram2" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram1" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram7" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram8" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram10" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram6" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram0" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram11" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram9" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram12" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram14" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram13" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram15" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop0" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop2" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop3" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop4" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop5" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop7" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock0" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop6" is skipped.
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img
fw_pkg_name: install.img
fw_pkg_name++++++: install.img


MAC вернул, а где 100 МБ прописать?
Egreat R160S (R160S-2.5.6.0-by-CSv2.0-DMD-XLCZv4.5)
Iconbit 1003DT2 (inext_hd1_2.22_r1)
Makc2
 
Posts: 24
Joined: 16 Jan 2017, 18:54

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 19 guests

cron