Добавление драйвера WiFi RTL8192CU

о железе плеера и о периферии

Re: Добавление драйвера WiFi RTL8192CU

Postby Юрий » 13 Sep 2011, 20:20

123serge123 wrote:Нашел багу - скомпилил снова. Интресна настройка в ГУИ. И вроде бы должен правильно показыать "палки" :)

Лог | +
Code: Select all
~ # lsmod
8192cu 587536 0 - Live 0xc03a3000
ohci_hcd 21904 0 - Live 0xc00d5000
ehci_hcd 40800 0 - Live 0xc00ca000
ufsd 624720 1 - Live 0xc014f000
venus_ir_new 12000 5 - Live 0xc008f000
sata_mars 22240 3 - Live 0xc005e000
libata 52720 1 sata_mars, Live 0xc0067000
~ # ifconfig wlan0 up
~ # iwlist wlan0 scan
wlan0     Scan completed :
          Cell 01 - Address: 74:EA:3A:A9:36:1A
                    ESSID:"tkt773259"
                    Protocol:IEEE 802.11bgn
                    Mode:Master
                    Frequency:2.412 GHz (Channel 1)
                    Encryption key:on
                    Bit Rates:150 Mb/s
                    Extra:wpa_ie=dd160050f20101000050f20401000050f20401000050f202
                    IE: WPA Version 1
                        Group Cipher : CCMP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    Extra:rsn_ie=30140100000fac040100000fac040100000fac020000
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : CCMP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    IE: Unknown: DD0E0050F204104A0001101044000102
                    Quality=62/100  Signal level=62/100 
          Cell 02 - Address: 54:E6:FC:DB:CC:9C
                    ESSID:"1Network"
                    Protocol:IEEE 802.11bgn
                    Mode:Master
                    Frequency:2.432 GHz (Channel 5)
                    Encryption key:on
                    Bit Rates:300 Mb/s
                    Extra:rsn_ie=30140100000fac040100000fac040100000fac020000
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : CCMP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    Quality=62/100  Signal level=62/100 
          Cell 03 - Address: 00:19:CB:58:E5:79
                    ESSID:"AscWiFi"
                    Protocol:IEEE 802.11bg
                    Mode:Master
                    Frequency:2.452 GHz (Channel 9)
                    Encryption key:off
                    Bit Rates:54 Mb/s
                    Quality=91/100  Signal level=91/100 
~ # iwconfig wlan0 essid "AscWiFi"
~ # /sbin/udhcpc -p /var/lock/udhcpc_wlan0.pid -t 15 -b -s /etc/udhcpc.script -i
 wlan0
udhcpc (v1.18.5) started
ifconfig wlan0 169.254.129.179
route add -net 0.0.0.0 netmask 0.0.0.0 wlan0
Sending discover...
Sending select for 192.168.1.33...
Lease of 192.168.1.33 obtained, lease time 604800
deleting routers
route: SIOCDELRT: No such process
adding dns 192.168.1.1
~ # dmesg
generic sg2 at scsi2, channel 0, id 0, lun 1,  type 0
  Vendor: Generic-  Model: SM/xD-Picture     Rev: 1.02
  Type:   Direct-Access                      ANSI SCSI revision: 00
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 2
Attached scsi generic sg3 at scsi2, channel 0, id 0, lun 2,  type 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
  Vendor: Generic-  Model: MS/MS-Pro         Rev: 1.03
  Type:   Direct-Access                      ANSI SCSI revision: 00
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 3
Attached scsi generic sg4 at scsi2, channel 0, id 0, lun 3,  type 0
usb-storage: device scan complete
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
+++ ALLOC index: 18976 order: 4
1. start remap DVR zone 86a20000(805ec400) 16...
map_done is 16...
+++ ALLOC index: 18992 order: 4
1. start remap DVR zone 86a30000(805ec600) 16...
2. redo mapping pages 2...
map_done is 14...
        retry remapping...
1. start remap DVR zone 86a30000(805ec600) 16...
map_done is 2...
--- FREE index: 18992 order: 4
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
usb 1-2: new high speed USB device using ehci_hcd and address 4
###################################################################
[cfyeh-test] usb_set_configuration(1454)
Don't support this usb device or don't insert correct module yet!!!
bus_id 1-2:1.0 (config #1, interface 0)
###################################################################

rtw driver version=v3.0.2164.20110715
CHIP TYPE: RTL8188C_8192C

usb_endpoint_descriptor(0):
bLength=7
bDescriptorType=5
bEndpointAddress=81
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_in = 1

usb_endpoint_descriptor(1):
bLength=7
bDescriptorType=5
bEndpointAddress=2
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 2

usb_endpoint_descriptor(2):
bLength=7
bDescriptorType=5
bEndpointAddress=3
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 3

usb_endpoint_descriptor(3):
bLength=7
bDescriptorType=5
bEndpointAddress=84
wMaxPacketSize=40
bInterval=1
RT_usb_endpoint_is_int_in = 4, Interval = 1
nr_endpoint=4, in_num=2, out_num=2

USB_SPEED_HIGH
Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
RF_Type is 3!!
EEPROM type is E-FUSE
====> ReadAdapterInfo8192C
Boot from EFUSE, Autoload OK !
EEPROMVID = 0x0bda
EEPROMPID = 0x8176
EEPROMCustomerID : 0x00
EEPROMSubCustomerID: 0x00
RT_CustomerID: 0x00
_ReadMACAddress MAC Address from EFUSE = 00:e0:4c:04:01:f5
EEPROMRegulatory = 0x0
_ReadBoardType(0)
BT Coexistance = disable
RT_ChannelPlan: 0x02
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
### PS params=>  power_mgnt(0),usbss_enable(0) ###
### AntDivCfg(0)
readAdapterInfo_8192CU(): REPLACEMENT = 1
<==== ReadAdapterInfo8192C in 270 ms
+++ ALLOC index: 18952 order: 3
1. start remap DVR zone 86a08000(805ec100) 8...
2. redo mapping pages 1...
map_done is 7...
        retry remapping...
1. start remap DVR zone 86a08000(805ec100) 8...
map_done is 1...
+++ ALLOC index: 18992 order: 3
1. start remap DVR zone 86a30000(805ec600) 8...
map_done is 0...
+++ ALLOC index: 19000 order: 3
1. start remap DVR zone 86a38000(805ec700) 8...
map_done is 0...
+++ ALLOC index: 19008 order: 3
1. start remap DVR zone 86a40000(805ec800) 8...
2. redo mapping pages 1...
map_done is 7...
        retry remapping...
1. start remap DVR zone 86a40000(805ec800) 8...
map_done is 1...
rtw_macaddr_cfg MAC Address  = 00:e0:4c:04:01:f5
MAC Address from pnetdev->dev_addr= 00:e0:4c:04:01:f5
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
usbcore: registered new driver rtl8192cu
+871x_drv - drv_open, bup=0
 ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
fw_ver=v75, fw_subver=0, sig=0x88c0
fw download ok!
Set RF Chip ID to RF_6052 and RF type to 1T1R.
GPIO_IN=0a
eRfPowerStateToSet=0
IQK:Start!!!
Path A IQK Success!!
Path A IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=101 RegE9C=13 RegEA4=fd RegEAC=3fd RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
 Path A IQ Calibration Success !
pdmpriv->TxPowerTrackControl = 1
MAC Address from REG_MACID = 00:e0:4c:04:01:f5
MAC Address = 00:e0:4c:04:01:f5
-871x_drv - drv_open, bup=1
IW_SCAN_THIS_ESSID, ssid=AscWiFi, len=7
survey done event(11)
+rtw_wx_set_enc, flags=0x8800
EncryptionDisabled
set_mode = IW_MODE_INFRA
=>rtw_wx_set_essid
ssid=AscWiFi, len=8
new candidate: AscWiFi(00:19:cb:58:e5:79) rssi:-50
rtw_select_and_join_from_scanned_queue: candidate: AscWiFi(00:19:cb:58:e5:79)
#### Opt_Ant_(B) , cur_Ant(B)
link to new AP
<=rtw_wx_set_essid
link to Realtek 96B
OnAuthClient
OnAssocRsp
report_join_res(2)
HW_VAR_BASIC_RATE: BrateCfg(0x15d)
HTOnAssocRsp
update raid entry, mask=0x40000fff, arg=0x80
rtl8192c_set_FwJoinBssReport_cmd mstatus(1)
SetFwRsvdPagePkt
--- FREE index: 18976 order: 4
Set RSVD page location to Fw.
=>mlmeext_joinbss_event_callback
rtl8192c_dm_RF_Saving(): RF_Normal
rtl8192c_dm_RF_Saving(): RF_Save
save exit: isCheckpointed 1
=>rtw_wx_set_essid
ssid=AscWiFi, len=8
new candidate: AscWiFi(00:19:cb:58:e5:79) rssi:-48
rtw_select_and_join_from_scanned_queue: candidate: AscWiFi(00:19:cb:58:e5:79)
rtw_select_and_join_from_scanned_queue: _FW_LINKED while ask_for_joinbss!!!
rtw_select_and_join_from_scanned_queue: _FW_LINKED and is same network, it needn't join again
<=rtw_wx_set_essid
save exit: isCheckpointed 1
survey done event(13)
+rtw_wx_set_enc, flags=0x8800
EncryptionDisabled
set_mode = IW_MODE_INFRA
=>rtw_wx_set_essid
ssid=AscWiFi, len=8
new candidate: AscWiFi(00:19:cb:58:e5:79) rssi:-45
rtw_select_and_join_from_scanned_queue: candidate: AscWiFi(00:19:cb:58:e5:79)
rtw_select_and_join_from_scanned_queue: _FW_LINKED while ask_for_joinbss!!!
rtw_select_and_join_from_scanned_queue: _FW_LINKED and is same network, it needn't join again
<=rtw_wx_set_essid
survey done event(12)
survey done event(1b)
save exit: isCheckpointed 1
(2)871x_drv - drv_close, bup=1, hw_init_completed=1
rtl8192c_set_FwJoinBssReport_cmd mstatus(0)
-871x_drv - drv_close, bup=1
+871x_drv - drv_open, bup=1
-871x_drv - drv_open, bup=1
rtl8192c_dm_RF_Saving(): RF_Normal
save exit: isCheckpointed 1
survey done event(21)
save exit: isCheckpointed 1
save exit: isCheckpointed 1
IQK:Start!!!
Path A IQK Success!!
Path A IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=102 RegE9C=e RegEA4=f9 RegEAC=3ff RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
 Path A IQ Calibration Success !
=>rtw_wx_set_essid
ssid=AscWiFi, len=8
new candidate: AscWiFi(00:19:cb:58:e5:79) rssi:-52
rtw_select_and_join_from_scanned_queue: candidate: AscWiFi(00:19:cb:58:e5:79)
#### Opt_Ant_(B) , cur_Ant(B)
link to new AP
<=rtw_wx_set_essid
link to Realtek 96B
OnAuthClient
OnAssocRsp
report_join_res(2)
HW_VAR_BASIC_RATE: BrateCfg(0x15d)
HTOnAssocRsp
update raid entry, mask=0x40000fff, arg=0x80
rtl8192c_set_FwJoinBssReport_cmd mstatus(1)
SetFwRsvdPagePkt
Set RSVD page location to Fw.
=>mlmeext_joinbss_event_callback
IW_SCAN_THIS_ESSID, ssid=AscWiFi, len=7
rtl8192c_dm_RF_Saving(): RF_Save
survey done event(12)
+rtw_wx_set_enc, flags=0x8800
EncryptionDisabled
set_mode = IW_MODE_INFRA
=>rtw_wx_set_essid
ssid=AscWiFi, len=8
new candidate: AscWiFi(00:19:cb:58:e5:79) rssi:-49
rtw_select_and_join_from_scanned_queue: candidate: AscWiFi(00:19:cb:58:e5:79)
rtw_select_and_join_from_scanned_queue: _FW_LINKED while ask_for_joinbss!!!
rtw_select_and_join_from_scanned_queue: _FW_LINKED and is same network, it needn't join again
<=rtw_wx_set_essid
survey done event(13)
save exit: isCheckpointed 1
save exit: isCheckpointed 1

~ # iwconfig wlan0
wlan0     IEEE 802.11bg  ESSID:"AscWiFi"  Nickname:"<WIFI@REALTEK>"
          Mode:Managed  Frequency:2.452 GHz  Access Point: 00:19:CB:58:E5:79   
          Bit Rate:54 Mb/s   Sensitivity:0/0 
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=98/100  Signal level=98/100  Noise level=0/100
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

~ # ifconfig wlan0
wlan0     Link encap:Ethernet  HWaddr 00:E0:4C:04:01:F5 
          inet addr:192.168.1.33  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:708 errors:0 dropped:3760 overruns:0 frame:0
          TX packets:193 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:54274 (53.0 KiB)  TX bytes:18302 (17.8 KiB)

ScreenCapture_2261.jpg
ScreenCapture_2261.jpg (40.29 KiB) Viewed 3510 times

Отправил в сон с пульта, включил - Шлюз потерялся:
ScreenCapture_2684.jpg
ScreenCapture_2684.jpg (33.35 KiB) Viewed 3510 times

Снова выключил с пульта, переткнул питание - настройки сети те же (с потерянным шлюзом).

Вы хотели проверить "палки".
"Настр.беспр.сети"->"Connection2"->Медиаплеер повис.
Переткнул питание, повторил "Настр.беспр.сети"->"Connection2"->Медиаплеер пошёл на перезагрузку, как показалось, тёплую.
ZyXEL Keenetic ¤—кабель—> WD Live 2Tb
ZyXEL Keenetic ¤—кабель—> Asus HD2 (amp r12+IconBIT) <=int hdd=> WD 2Tb (WD Aling) (512Мб swap | 1.5Тб NTFS | 450Гб NTFS)
User avatar
Юрий
 
Posts: 67
Joined: 25 Mar 2011, 11:48

Re: Добавление драйвера WiFi RTL8192CU

Postby 123serge123 » 14 Sep 2011, 19:16

Потеря шлюза в данном случае не показатель - при наличие второго (проводного) интерфейса назначение второго дефолтового маршрута ведет себя загадочно :). Для исключения влияния проводов желательно повторить всё с единственным беспроводным интерфейсом. Подключение по кабелю только для сбора логов после окончания очередного эксперимента.
Как остальные тесты продвигаются? Особенно в части ГУИ и соединения с шифрованием.
123serge123
 
Posts: 186
Joined: 02 Oct 2010, 08:49

Re: Добавление драйвера WiFi RTL8192CU

Postby Юрий » 21 Oct 2011, 21:08

123serge123 wrote:Как остальные тесты продвигаются? Особенно в части ГУИ и соединения с шифрованием.

Настроил таки я это шифрование (WPA2)! Настроил шифрование и у зверька (не без бубнов). Работает.
Но! Так и осталась одна проблемка:
Настройки->Сеть->Настр.беспр. сети->Инфраструктура (AP)-> зверёк пару секунд думает и идёт на перезагрузку.
ZyXEL Keenetic ¤—кабель—> WD Live 2Tb
ZyXEL Keenetic ¤—кабель—> Asus HD2 (amp r12+IconBIT) <=int hdd=> WD 2Tb (WD Aling) (512Мб swap | 1.5Тб NTFS | 450Гб NTFS)
User avatar
Юрий
 
Posts: 67
Joined: 25 Mar 2011, 11:48

Re: Добавление драйвера WiFi RTL8192CU

Postby 123serge123 » 21 Oct 2011, 21:58

В сторону бубны, за месяц пути собачка подросла :).
Последняя версия драйвера вполне рабочая.
Attachments
8192cu.zip
(181.33 KiB) Downloaded 204 times
123serge123
 
Posts: 186
Joined: 02 Oct 2010, 08:49

Re: Добавление драйвера WiFi RTL8192CU

Postby Юрий » 23 Oct 2011, 17:21

Поставил прошивку amp_r5_hd2, WiFi определился. Но поиск по Настройки->Сеть->Настр.беспр. сети->Инфраструктура (AP)-> Говорит, что ничего нет.
123serge123 wrote:В сторону бубны, за месяц пути собачка подросла :).
Последняя версия драйвера вполне рабочая.
Подсунул эту версию 8192cu поверх /lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/rtl8192DU/8192du.ko
Настройки->Сеть->Настр.беспр. сети->Инфраструктура (AP)->Выдал список точек, выбрал нужную, спросил пароль, подключился и даже заработал!

А можно эту версию драйвера положить сразу в следующую прошивку, чтобы после перепрошивания не пришлось тянуть кабель от "зверька" к роутеру?
ZyXEL Keenetic ¤—кабель—> WD Live 2Tb
ZyXEL Keenetic ¤—кабель—> Asus HD2 (amp r12+IconBIT) <=int hdd=> WD 2Tb (WD Aling) (512Мб swap | 1.5Тб NTFS | 450Гб NTFS)
User avatar
Юрий
 
Posts: 67
Joined: 25 Mar 2011, 11:48

Re: Добавление драйвера WiFi RTL8192CU

Postby Юрий » 23 Oct 2011, 18:21

Выбрал сеть:
sc_ScreenCapture_3667.jpg
sc_ScreenCapture_3667.jpg (25.96 KiB) Viewed 3432 times

в сон-проснуться:
IMG_0242.JPG
IMG_0242.JPG (41.46 KiB) Viewed 3432 times

Это связано с драйвером или с версией прошивки?
ZyXEL Keenetic ¤—кабель—> WD Live 2Tb
ZyXEL Keenetic ¤—кабель—> Asus HD2 (amp r12+IconBIT) <=int hdd=> WD 2Tb (WD Aling) (512Мб swap | 1.5Тб NTFS | 450Гб NTFS)
User avatar
Юрий
 
Posts: 67
Joined: 25 Mar 2011, 11:48

Re: Добавление драйвера WiFi RTL8192CU

Postby Virtual » 23 Oct 2011, 18:45

это связано с "мочиловом" модулей перед сном.... и если убиты- последующим взлетом :).

//хвосты от частей "отреалтека" в коде прошивок. проблема ясна- модуль не убит перед сном. и гуй его не настроил после....
ЗЫ когда-нить може-быть исправим :).

ЗЫЗЫ ваш драйвер офф прошивки не знают и "мочить" соответственно не умеют :mrgreen:
//кст на скинах HD2 скриншот можно снять из вэбморды...
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.84 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6300
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Добавление драйвера WiFi RTL8192CU

Postby Юрий » 23 Oct 2011, 20:05

Virtual wrote:***
//кст на скинах HD2 скриншот можно снять из вэбморды...
Спасибо, я знаю, только если WiFi не поднялся, то для "скриншота можно снять из вэбморды" надо кабель тянуть. ;)
ZyXEL Keenetic ¤—кабель—> WD Live 2Tb
ZyXEL Keenetic ¤—кабель—> Asus HD2 (amp r12+IconBIT) <=int hdd=> WD 2Tb (WD Aling) (512Мб swap | 1.5Тб NTFS | 450Гб NTFS)
User avatar
Юрий
 
Posts: 67
Joined: 25 Mar 2011, 11:48

Re: Добавление драйвера WiFi RTL8192CU

Postby subeditor » 15 Dec 2013, 22:16

Всем доброго времени суток!
Скажите, прокатит ли описанное здесь волшебство для 3Q F425HW? Или, может быть, дрова для RTL8192CU уже включены в какой-нибудь пакет/прошивку, просто я их не нашел?

Заранее спасибо.
3Q F425HW
subeditor
 
Posts: 3
Joined: 15 Dec 2013, 11:27

Re: Добавление драйвера WiFi RTL8192CU

Postby Virtual » 17 Dec 2013, 21:17

Эти драйвера уже есть в AMP11 (для чипстов 1073/1283)

Но для 1185, увы только те, что есть в прошивках.
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.84 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6300
Joined: 01 Oct 2010, 17:17
Location: UFA RU

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 4 guests