Поднимаем кирпич

Re: Поднимаем кирпич

Postby bsb5068 » 01 Jun 2013, 18:29

что-то не видит как будто прошивки.
Лог | +
Code: Select all
5280 wai5t280 waiA~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A
~A~A~A~A~A~A~A~A~A~A~A~A????????????
REALTEK ROM Monitor, Revision 0000.0202.1019.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /.version=     Feb 13 2013  02:48:16  /0000.0202.1019
MAC address =                   00.11.22.33.44.55
Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision =         0x93 / 0x78
Endianness =                    Little
Flash memory size =             128 MByte
SDRAM size =                    128 MByte
First free SDRAM address =      0x8010d000

Press 'ESC' to Monitor mode
Signature(яяяяяяяя) error! Entering rescue linux...
PAL logo
PAL logo
Rescue kernel in FLASH, total size = 0x144533

            seg.1 addr 0xa0a097e4, size = 0x144533

            seg.2 addr 0x0, size = 0x0
copy rescue0: from a0a097e4 to 81000000, len = 144533
decompressing rescue: from 81000000 to 80100000: size = 144533
lzma finished
decompressing rescue done
go 0x80100000 BOOT_TAG=яяяяяяяя
PAL logo
Reset Ethernet Mac.


Address = 0x80100000

Realtek LINUX (DC ALIAS) started...
Venus setting:
        ROSs have 2621440 bytes RAM.
        System CPU has 1 UART.
        System CPU uses external timer interrupt.
        Bootloader version: 0000.0202.1019. This version string is of new format
.
        The information of this board: Company ID:0x0    CPU ID: 0x32    Board I
D: 0x202
        Ethernet Mac address: 00.11.22.33.44.55
        Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x08000000
Linux version 2.6.12.6-VENUS (vadmin@vadmin) (gcc version 3.4.4 mipssde-6.03.01-
20051114) #323636_r9.1 Fri Feb 8 10:39:27 OMST 2013
**************************************************************
You didn't specify audio image address, use default instead...
**************************************************************
audio addr: 0
CPU revision is: 00019378
Determined physical RAM map:
 memory: 00100000 @ 00000000 (usable)
 memory: 00348000 @ 00100000 (reserved)
 memory: 01938000 @ 00448000 (usable)
 memory: 00280000 @ 01d80000 (reserved)
 memory: 06000000 @ 02000000 (usable)
  show info: max_low_pfn:32768
  show info: min_low_pfn:1096
Built 1 zonelists
Kernel command line: BOOT_TAG=яяяяяяяя console=ttyS0,115200n8r ip=192.168.0.9::1
92.168.0.254:255.0.0.0:::
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 256 (order: 8, 4096 bytes)
Estimate value: CPU frequency 405.02 MHz
Using 27.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 123008k/125152k available (2334k kernel code, 2112k reserved, 338k data,
 608k init, 0k highmem)
Warning! Unknown board id.
Warning! Unknown board id.
==================== Warning! The calculated loops_per_jiffy is not similar to t
he default one. ====================
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SCSI subsystem initialized
se init module major number = 254
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
[user land] CmdBuf virt addr = 80580000/a0580000, phy addr=00580000
   Hello, Realtek TLB Mapper
   AllocBP size: 294912 order: 7
        <<<DVR FREE AREA>>>
        0:      0
        1:      0
        2:      0
        3:      0
        4:      0
        5:      0
        6:      0
        7:      0
        8:      0
        9:      0
        10:     0
        11:     0
        12:     6
                Addr: 87000000, order: 12
                Addr: 86000000, order: 12
                Addr: 85000000, order: 12
                Addr: 84000000, order: 12
                Addr: 83000000, order: 12
                Addr: 82000000, order: 12
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
NTFS driver 2.1.28 [Flags: R/O].
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize
loop: loaded (max 8 devices)
this  MARS eth RX_OFFSET = 0x0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
MAC address = 0x00.11.22.33.44.55
eth0: RTL-8139C+ at 0xb8016000, 00:11:22:33:44:55, IRQ 2
cp_hotplug
physmap flash device: 8000000 at 17d00000
Realtek NAND Flash Driver Rev:317223 (2010-06-01)
One HY27UF081G2A chip has 1 die(s) on board
nand part=HY27UF081G2A, id=adf1801d, device_size=134217728, chip_size=134217728,
 num_chips=1, isLastPage=0
[NF_CKSEL] HY27UF081G2A is set to nf clock: 0x3
[rtk_nand_scan_bbt] have created bbt B0, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
RTK: using the whole nand as a partitoin
Realtek Nand Flash Driver is successfully installing.
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 0
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 0
#@# cfyeh-debug USBPHY_SetReg_Default_39(417) tx_delay 1
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ehci_hcd ehci_hcd: EHCI Host Controller
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub : individual port power switching
hub : individual port over-current protection
Hotplug got one Net Hotplug of "Add" from "eth0". It may be Realtek's wireless d
evice.
Hotplug got one Net Hotplug of "Add" from "lo". It may be Realtek's wireless dev
ice.
[cfyeh] set PPE = 0
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 0
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 0
#@# cfyeh-debug USBPHY_SetReg_Default_39(417) tx_delay 1
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection
Initializing USB Mass Storage driver...
usb 1-2: new high speed USB device using ehci_hcd and address 2
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
hub : individual port power switching
hub : individual port over-current protection
Hotplug got one USB Hotplug of "Add" from port "2".
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Setting registers , Enable OTG
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Shared Tx FIFO mode
DWC_otg: Using DMA mode
dwc_otg lm1: DWC OTG Controller
dwc_otg lm1: new USB bus registered, assigned bus number 3
dwc_otg lm1: irq 2, io mem 0x00000000
DWC_otg: USB RESET BY HOST
gadgetfs: USB Gadget filesystem, version 24 Aug 2004
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODE: MARS/JUPITER
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 8
= RX FIFO DEPTH : 8
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : OFF
= GPIO RW SUPPORT : ON
=========================
[I2C1] i2c speed changed to 100 KHz
I2C1 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 1
= MODE: MARS/JUPITER
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 8
= RX FIFO DEPTH : 8
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : OFF
= GPIO RW SUPPORT : ON
=========================
libata version 1.12 loaded..
sata driver initial...2009/12/30 14:50
sata driver patched 2013/02/07 (Virtual)
mars_init_sata(1270)dev_addr:80398608
ata_device_add(4893)probe begin
scsi0 : SATA_DRV
sata dma reset
usb 1-2.2: new high speed USB device using ehci_hcd and address 3
hub 1-2.2:1.0: USB hub found
hub 1-2.2:1.0: 1 port detected
hub : individual port power switching
hub : individual port over-current protection
Hotplug got one USB Hotplug of "Add" from port "2.2".
RTK rtc can work.
usb 1-2.2.1: new high speed USB device using ehci_hcd and address 4
scsi2 : SCSI emulation for USB Mass Storage devices
Hotplug got one USB Hotplug of "Add" from port "2.2.1".
sata1: no device found (phy stat 00000000)
sata1: ata_bus_probe failed
scsi1 : SATA_DRV
sata dma reset
sata2: no device found (phy stat 00000000)
sata2: ata_bus_probe failed
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
cp_open
alloc rings cp->rxdesc_buf =0xa1c4f000 , cp->ring_dma=0x1c4f000
init_hw
init_hw finished
IP-Config: Complete:
      device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
     host=192.168.0.9, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
Freeing prom memory: 0kb freed
Reclaim bootloader memory from 80020000 to 80100000
Freeing unused kernel memory: 608k freed
Hotplug: device "ram0" is skipped.
Hotplug: device "loop1" is skipped.
Hotplug: device "loop2" is skipped.
Hotplug: device "loop3" is skipped.
Hotplug: device "loop5" is skipped.
Hotplug: device "loop6" is skipped.
Hotplug: device "loop7" is skipped.
Hotplug: device "mtdblock0" is skipped.
Hotplug: device "loop0" is skipped.
Hotplug: device "loop4" is skipped.
  Vendor: USB 2.0   Model: Flash Disk        Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 2002944 512-byte hdwr sectors (1026 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 2002944 512-byte hdwr sectors (1026 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
 /dev/scsi/host2/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0,  type 0
rmdir: '/var/lock/hotplug/mount_tmp/.sda': No such file or directory
rmdir: '/var/lock/hotplug/mount_tmp/.sda1': No such file or directory
Hotplug: "sda" has partitions.
mount: mounting /dev/scsi/host2/bus0/target0/lun0/part1 on /var/lock/hotplug/mou
nt_tmp/.sda1 failed: No such device
modprobe: module sd_mod not found in modules.dep
mount: mounting /dev/scsi/host2/bus0/target0/lun0/part1 on /var/lock/hotplug/mou
nt_tmp/.sda1 failed: Invalid argument
#######[cfyeh-debug] device_name_translating(224) open /sys/block/sda1/part_num
fail!
Hotplug: mount -t ufsd -o ro,sparse -o nls=utf8 -o umask=0 /dev/scsi/host2/bus0/
target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1    ret: 255
Hotplug: mount -t ntfs -o ro -o nls=utf8 -o umask=0 /dev/scsi/host2/bus0/target0
/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1   ret: 255
Hotplug: mount -t vfat -o ro,shortname=winnt -o utf8 -o umask=0 /dev/scsi/host2/
bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1       ret: 0
part number: 1 (env)
extended number: 0 (env)
sequence value: 0 (env)
reserve 2, name: sda1
cmd_buffer: ln -s /tmp/usbmounts/sda1 /tmp/ramfs/volumes/C:
Hotplug: Mount "sda1" successfully.
Hotplug got one BLOCK Hotplug of "Add" from "sda1"
Hotplug got one BLOCK Hotplug of "Ready" from "sda1"
udhcpc (v1.18.5) started
120+0 records in
120+0 records out
61440 bytes (60.0KB) copied, 0.003621 seconds, 16.2MB/s
Welcome to Virtual :) Rescue Linux
mount: mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such devic
e
Sending discover...
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directo
ry
Sending discover...

>>>>>> loader start! (Mar 26 2012:17:11:26, version=00.01.01)
/
pwd....dd://dev/mtdblock/0/
loader [0]: Execute Verona Loader load_func failed!

>>>>>> loader exit!

Please press Enter to activate this console. Sending discover...



BusyBox v1.18.5 (2012-07-06 14:41:16 OMSST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

пробую другую флэшку.
запаять побольше? 256 хватит или лучшк 512?
а кроме мака ещё же какой то board id нужен или что ещё?
Seagate Freeagent Theater plus (RTD1073MD -> RTD1073DD, unkn_NAND -> 8Gbit_NAND, Additional_SATA_mod, AsusBOOT_V23), AMP R10, eth0
bsb5068
 
Posts: 86
Joined: 13 Jan 2012, 10:23
Location: Cherepovets

Re: Поднимаем кирпич

Postby Virtual » 01 Jun 2013, 18:37

погодь пока флешки паять! я в логе не вижу что плеер видит USB флеху с прошивкой.
питание на USB есть?
если когда в логе появится что флешка смонтировалась....
но лоадер вылетит с таким логом

loader [0]: Execute Verona Loader load_func failed!

>>>>>> loader exit!

просто с консоли набрать
loader_a
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Поднимаем кирпич

Postby FarVoice » 01 Jun 2013, 18:40

походу, у вас ваще флешки нету ;)
pwd....dd://dev/mtdblock/0/
loader [0]: Execute Verona Loader load_func failed!

Да и сообщений mtd драйвера не было...
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Поднимаем кирпич

Postby bsb5068 » 01 Jun 2013, 18:42

USB видит.
ls /tmp/usbmounts/sda1 выдаёт файлы на ней.

| +
~ # ls
Test.fat dev init mnt sbin tmp usr
bin etc lib proc sys tmp_orig var
~ # ls /tmp/usbmounts/sda1
$$ystemupdate
BlackBox_FTP_Server_v1.2_Waninkoko_Kmeaw_CFW_3.55_Stealth_ID.pkg
NewFile0.csv
NewFile0.txt
NewFile0.wfm
NewFile1.csv
NewFile1.txt
install.img
multiMAN ver 04.30.00 BASE CEX (20130324).pkg
ps3
~ #


походу, у нас ваще флешки какой нету? NANDa? ;)
Last edited by bsb5068 on 01 Jun 2013, 20:52, edited 2 times in total.
Seagate Freeagent Theater plus (RTD1073MD -> RTD1073DD, unkn_NAND -> 8Gbit_NAND, Additional_SATA_mod, AsusBOOT_V23), AMP R10, eth0
bsb5068
 
Posts: 86
Joined: 13 Jan 2012, 10:23
Location: Cherepovets

Re: Поднимаем кирпич

Postby FarVoice » 01 Jun 2013, 18:44

аха :) Внутренней NAND флеши
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Поднимаем кирпич

Postby bsb5068 » 01 Jun 2013, 18:45

есть....было так скажем в первом логе
| +
Realtek NAND Flash Driver Rev:317223 (2010-06-01)
One HY27UF081G2A chip has 1 die(s) on board
nand part=HY27UF081G2A, id=adf1801d, device_size=134217728, chip_size=134217728,

оно видимо просто не разбито.
| +
/dev/mtdblock # ls
0

cat 0 выдаёт содержимое
Last edited by bsb5068 on 01 Jun 2013, 20:53, edited 1 time in total.
Seagate Freeagent Theater plus (RTD1073MD -> RTD1073DD, unkn_NAND -> 8Gbit_NAND, Additional_SATA_mod, AsusBOOT_V23), AMP R10, eth0
bsb5068
 
Posts: 86
Joined: 13 Jan 2012, 10:23
Location: Cherepovets

Re: Поднимаем кирпич

Postby FarVoice » 01 Jun 2013, 18:50

а что за странный сайз у вашей флешки? 128 метров - маловато что-то...
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: Поднимаем кирпич

Postby Virtual » 01 Jun 2013, 18:54

если просто набрать loader_a
вылетает? (есть такой глючек за ним :( при полностью стертой таблице разделов) как нить починю на досуге

но это не страшно....
все можно и ручками запустить...
кст у вас ща бут с потдержкой сети! мона даже к инету его подрубить :)

ЗЫ а я в баню, так что оставлю вас на несколько часов - развлекайтесь....
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Поднимаем кирпич

Postby bsb5068 » 01 Jun 2013, 18:56

набрал loader_a
он начал на что то ругаться что всё не то и отсутствует но ставится. прогресс пошёл....:) спасибо! :)
прошился даже заставки и огонёк на пульт реагурет толкьо ничего не работает. видимо пульт от сигейта не подходит....
Seagate Freeagent Theater plus (RTD1073MD -> RTD1073DD, unkn_NAND -> 8Gbit_NAND, Additional_SATA_mod, AsusBOOT_V23), AMP R10, eth0
bsb5068
 
Posts: 86
Joined: 13 Jan 2012, 10:23
Location: Cherepovets

Re: Поднимаем кирпич

Postby bsb5068 » 01 Jun 2013, 18:59

так или там была на 128 или я перепутал не ту впаял :roll:
Seagate Freeagent Theater plus (RTD1073MD -> RTD1073DD, unkn_NAND -> 8Gbit_NAND, Additional_SATA_mod, AsusBOOT_V23), AMP R10, eth0
bsb5068
 
Posts: 86
Joined: 13 Jan 2012, 10:23
Location: Cherepovets

PreviousNext

Return to Seagate

Who is online

Users browsing this forum: No registered users and 8 guests