NFS сервер на плеере

Re: NFS сервер на плеере

Postby Virtual » 14 Oct 2011, 15:02

хм винт без партиций..... если плеер флешки такие еще как-то терпит... то имхо винт в таком виде для него странность :)...
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: NFS сервер на плеере

Postby -uragan- » 15 Oct 2011, 09:39

Ребят, спасибо огромное за советы
так и сделаю сейчас! :)
R6S (Bast Castle v1.04 Mod2)
-uragan-
 
Posts: 195
Joined: 16 May 2011, 11:35
Location: Германия

Re: NFS сервер на плеере

Postby -uragan- » 28 Oct 2011, 11:10

форматнул винт в ext3, сделал одну партицию.
зверек ее всегда распознает как sda1 но вырубаться так и не хочет...
как еще можно попробовать с этим побороться?

просто каждый раз выдергивать вилку это на вариант :(
R6S (Bast Castle v1.04 Mod2)
-uragan-
 
Posts: 195
Joined: 16 May 2011, 11:35
Location: Германия

Re: NFS сервер на плеере

Postby Virtual » 28 Oct 2011, 14:32

как еще можно попробовать с этим побороться?

1. поставить последнюю актуальную (AMPр5)
2. ничего не трогать! все флешки диски отрубить, проверить на предмет отключенного автосканирования
2.1 если телик не по HDMI то поставить модуль Hdcp Off //никаких других модулей более недоустанавливать/удалять.
3. вилку из розетки долой.... потом вкл.... подождать пару минут... выключается?
4 в выключеный плеер добавить диск (кст USB или SATA ?)
5. включить.... подождать 5 минут минимум (ничего не трогать!).... выключить пультом.... выключается?
если нет..... дать 10минут плееру на обдумывание .... и результат сюда:
Code: Select all
dmesg
lsmod
ifconfig
df
mount
ps

|лог получится длинный так что принять меры к его сохранению :)|
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: NFS сервер на плеере

Postby -uragan- » 29 Oct 2011, 08:40

сделал все так, как Вы сказали.
диск подключен по SATA

все так и не хочет вырубаться.
вот лог, я подозрительного ничего не нашел... :(

| +
dmesg
map_done is 0...
+++ ALLOC index: 18976 order: 4
1. start remap DVR zone 86a20000(8061b400) 16...
map_done is 0...
--- FREE index: 19008 order: 6
--- FREE index: 18976 order: 4
+++ ALLOC index: 19008 order: 6
1. start remap DVR zone 86a40000(8061b800) 64...
map_done is 0...
+++ ALLOC index: 18976 order: 5
1. start remap DVR zone 86a20000(8061b400) 32...
map_done is 0...
--- FREE index: 19008 order: 6
--- FREE index: 18976 order: 5
+++ ALLOC index: 19008 order: 6
1. start remap DVR zone 86a40000(8061b800) 64...
map_done is 0...
+++ ALLOC index: 18976 order: 4
1. start remap DVR zone 86a20000(8061b400) 16...
map_done is 0...
--- FREE index: 19008 order: 6
--- FREE index: 18976 order: 4
+++ ALLOC index: 19008 order: 6
1. start remap DVR zone 86a40000(8061b800) 64...
map_done is 0...
+++ ALLOC index: 18976 order: 4
1. start remap DVR zone 86a20000(8061b400) 16...
map_done is 8...
--- FREE index: 19008 order: 6
--- FREE index: 18976 order: 4
+++ ALLOC index: 6656 order: 9
1. start remap DVR zone 83a00000(805bb000) 512...
map_done is 0...
+++ ALLOC index: 19072 order: 7
1. start remap DVR zone 86a80000(8061c000) 128...
map_done is 128...
--- FREE index: 6656 order: 9
--- FREE index: 19072 order: 7
sata2: phy reset timeout!
sata2: no device found (phy stat 00000000)
sata2: ata_bus_probe failed
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ehci_hcd ehci_hcd: EHCI Host Controller
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub : individual port power switching
hub : individual port over-current protection
[cfyeh] set PPE = 0
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub : individual port power switching
hub : individual port over-current protection
This is the current time: PowerUP_Done!!!
usb 1-1.3: new high speed USB device using ehci_hcd and address 3
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
save exit: isCheckpointed 1
EXT3 FS on sda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on loop2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
save exit: isCheckpointed 1
Vendor: Generic- Model: SD/MMC Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0, type 0
Vendor: Generic- Model: Compact Flash Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 1
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 1, type 0
Vendor: Generic- Model: SM/xD-Picture Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 00
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 2
Attached scsi generic sg3 at scsi2, channel 0, id 0, lun 2, type 0
Vendor: Generic- Model: MS/MS-Pro Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 00
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
###### [cfyeh] sdkp->media_present == 1, sdkp->capacity == 0
--- FREE index: 6144 order: 9
--- FREE index: 4096 order: 11
--- FREE index: 20480 order: 12
--- FREE index: 8192 order: 12
--- FREE index: 18944 order: 3
--- FREE index: 12288 order: 12
--- FREE index: 19456 order: 10
--- FREE index: 18432 order: 9
--- FREE index: 17408 order: 9
--- FREE index: 17920 order: 7
--- FREE index: 18048 order: 7
--- FREE index: 18176 order: 8
Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 3
Attached scsi generic sg4 at scsi2, channel 0, id 0, lun 3, type 0
usb-storage: device scan complete
clear pli setting....
***128MB version...
Memory address 0x40000000
[mtdblock_release] Done
[RPC]open for RPC ioctl...
[RPC]start reset...
[RPC]done...
release address: 86000000
--- FREE index: 16384 order: 10
release address: 86a10000
--- FREE index: 18960 order: 4
save exit: isCheckpointed 1
sata module is ready for service.
show_offline_dev_field(1310)dev_addr=c00632a0;
sata1 :device0 found
sata2 :device1 not found
mars_sata_work_fn
device removed from sata port0
mars_sata_work_fn(1141): no cmd Q
__scsi_remove_device(886)
mars_sata_work_fn(1172) hot plug end
device removed from sata port1
mars_sata_work_fn(1141): no cmd Q
mars_sata_work_fn(1172) hot plug end
ohci_hcd ohci_hcd: remove, state 1
usb usb2: USB disconnect, address 1
ohci_hcd ohci_hcd: USB bus 2 deregistered
ehci_hcd ehci_hcd: remove, state 1
usb usb1: USB disconnect, address 1
usb 1-1: USB disconnect, address 2
usb 1-1.3: USB disconnect, address 3
__scsi_remove_device(886)
devfs_remove: scsi/host2/bus0/target0/lun1/generic not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun1/disc not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun1 not found, cannot remove
__scsi_remove_device(886)
devfs_remove: /dev/scsi/host2 not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun2/generic not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun2/disc not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun2 not found, cannot remove
__scsi_remove_device(886)
devfs_remove: /dev/scsi/host2 not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun3/generic not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun3/disc not found, cannot remove
devfs_remove: scsi/host2/bus0/target0/lun3 not found, cannot remove
__scsi_remove_device(886)
devfs_remove: /dev/scsi/host2 not found, cannot remove
ehci_hcd ehci_hcd: USB bus 1 deregistered

lsmod
ufsd 624720 0 - Live 0xc014f000
venus_ir_new 12000 4 - Live 0xc008f000
sata_mars 22240 1 - Live 0xc005e000
libata 52720 1 sata_mars, Live 0xc0067000

ipconfig
eth0 Link encap:Ethernet HWaddr 20:CF:30:CE:9E:8A
inet addr:192.168.178.20 Bcast:192.168.178.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:129 errors:0 dropped:0 overruns:0 frame:0
TX packets:171 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10475 (10.2 KiB) TX bytes:66928 (65.3 KiB)
Interrupt:2 Base address:0x6000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 468736 74176 394560 16% /
/dev/mtdblock/2 4096 2572 1524 63% /usr/local/etc
/dev/rd/0 40 40 0 100% /mnt/rd
/dev/root 468736 74176 394560 16% /usr/local/etc/mos
/dev/loop/0 15424 15424 0 100% /usr/local/bin
/dev/loop/1 12736 12736 0 100% /usr/local/bin/Resource

mount
rootfs on / type rootfs (rw)
/dev/root on / type yaffs2 (rw,noatime)
none on /dev type devfs (rw)
none on /proc type proc (rw,nodiratime)
devpts on /dev/pts type devpts (rw)
none on /sys type sysfs (rw)
none on /tmp type ramfs (rw)
/dev/mtdblock/2 on /usr/local/etc type yaffs (rw,noatime)
/dev/rd/0 on /mnt/rd type vfat (rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
/dev/root on /usr/local/etc/mos type yaffs2 (rw,noatime)
/dev/loop/0 on /usr/local/bin type squashfs (ro)
/dev/loop/1 on /usr/local/bin/Resource type squashfs (ro)

ps
PID Uid VmSize Stat Command
1 root 2116 S init
2 root 0 SWN [ksoftirqd/0]
3 root 0 SW< [events/0]
4 root 0 SW< [khelper]
5 root 0 SW< [kthread]
6 root 0 SW< [kblockd/0]
7 root 0 SW [khubd]
8 root 0 SW [rpc-1]
9 root 0 SW [rpc-3]
10 root 0 SW [pdflush]
11 root 0 SW [pdflush]
13 root 0 SW< [aio/0]
14 root 0 SW< [cifsoplockd]
15 root 0 SW< [cifsdnotifyd]
12 root 0 SW [kswapd0]
17 root 0 SW [eth0]
18 root 0 SW [mtdblockd]
16 root 0 SW [kseriod]
25 root 2116 S init
26 root 2116 S init
29 root 2116 S init
32 root 2116 S init
108 root 2340 S inetd
118 root 0 SW< [sata_eh/0]
122 root 0 SW [scsi_eh_0]
123 root 0 SW [scsi_eh_1]
131 root 0 SW< [loop0]
134 root 0 SW< [loop1]
142 root 428 S /usr/local/etc/irfake/irfake4 -R -f /usr/local/etc/irfake/irfake.conf
146 root 768m S ./RootApp DvdPlayer
152 root 768m S ./RootApp DvdPlayer
301 root 0 SWN [kjournald]
402 root 0 SW< [loop2]
406 root 2332 R telnetd -i
407 root 2340 S -sh
669 root 2332 S sh -c echo mem>/sys/power/state
700 root 2332 R ps


Может Вы что нибудь найдете. Большое спасибо!
R6S (Bast Castle v1.04 Mod2)
-uragan-
 
Posts: 195
Joined: 16 May 2011, 11:35
Location: Германия

Re: NFS сервер на плеере

Postby Virtual » 29 Oct 2011, 09:07

-uragan-
.телик подрублен по HDMI? если да то попробуйте сначало провод выдернуть HDMI ;)
.попробуйте поставить модуль SMART HDD Tool (smartctl 5.41) обязательно перезагрузится!, и проверить.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: NFS сервер на плеере

Postby -uragan- » 29 Oct 2011, 10:28

1. выдернул HDMI , все равно не выключается
2. вот результат SMART HDD Tool

| +
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F1 DT
Device Model: SAMSUNG HD103UJ
Serial Number: S13PJ90S321575
LU WWN Device Id: 5 0024e9 2006599b5
Firmware Version: 1AA01113
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Sat Oct 29 10:22:36 2011 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11882) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 199) minutes.
Conveyance self-test routine
recommended polling time: ( 21) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0
3 Spin_Up_Time POS--- 093 093 011 - 3140
4 Start_Stop_Count -O--CK 099 099 000 - 1187
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
7 Seek_Error_Rate POSR-- 253 253 051 - 0
8 Seek_Time_Performance P-S--K 100 100 015 - 9922
9 Power_On_Hours -O--CK 100 100 000 - 1809
10 Spin_Retry_Count PO--CK 100 100 051 - 0
11 Calibration_Retry_Count -O--C- 100 100 000 - 0
12 Power_Cycle_Count -O--CK 099 099 000 - 1067
13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0
183 Runtime_Bad_Block -O--CK 100 100 000 - 10
184 End-to-End_Error PO--CK 100 100 000 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 0
188 Command_Timeout -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 068 052 000 - 32 (Min/Max 32/36)
194 Temperature_Celsius -O---K 069 051 000 - 31 (0 126 39 26)
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 2188
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 39
200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0
201 Soft_Read_Error_Rate -O-R-- 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning

General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log]
GP Log at address 0x04 has 2 sectors [Device Statistics]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 2 sectors [Write stream error log]
GP Log at address 0x22 has 2 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 39 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 39 [6] occurred at disk power-on lifetime: 1575 hours (65 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 53 00 8b 00 00 5e f0 0a 01 40 00 Error: ABRT 139 sectors at LBA = 0x5ef00a01 = 1592789505

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 03 00 f0 00 00 5e f0 09 9c 40 00 00:18:31.520 WRITE DMA EXT
35 00 03 00 f0 00 00 5e f0 08 ac 40 00 00:18:31.510 WRITE DMA EXT
35 00 03 00 f0 00 00 5e f0 07 bc 40 00 00:18:31.510 WRITE DMA EXT
35 00 03 00 f0 00 00 5e f0 06 cc 40 00 00:18:31.500 WRITE DMA EXT
35 00 03 00 f0 00 00 5e f0 05 dc 40 00 00:18:31.500 WRITE DMA EXT

Error 38 [5] occurred at disk power-on lifetime: 1519 hours (63 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 37 00 00 0b a1 ee 2d e0 00 Error: ICRC, ABRT 55 sectors at LBA = 0x0ba1ee2d = 195161645

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 00 70 00 00 0b a1 ed f4 e0 00 00:01:13.510 WRITE DMA EXT
35 00 00 00 80 00 00 0b a1 ec 64 e0 00 00:01:13.510 WRITE DMA EXT
35 00 00 01 40 00 00 0b a1 e7 54 e0 00 00:01:13.510 WRITE DMA EXT
35 00 00 01 50 00 00 0b a1 c9 ac e0 00 00:01:13.500 WRITE DMA EXT
35 00 00 00 18 00 00 0b a1 c9 84 e0 00 00:01:13.500 WRITE DMA EXT

Error 37 [4] occurred at disk power-on lifetime: 853 hours (35 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 48 00 03 00 00 00 60 8b 39 40 00 at LBA = 0x00608b39 = 6327097

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 08 00 00 00 60 8b 34 40 00 01:23:01.960 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 8a b4 40 00 01:23:01.960 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 85 04 40 00 01:23:01.960 WRITE FPDMA QUEUED
00 00 00 00 01 00 00 00 00 00 01 a0 00 01:23:01.950 NOP [Abort queued commands]

Error 36 [3] occurred at disk power-on lifetime: 853 hours (35 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 48 00 03 00 00 00 60 85 09 40 00 at LBA = 0x00608509 = 6325513

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 08 00 00 00 60 85 04 40 00 01:23:01.940 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 77 8c 40 00 01:23:01.940 WRITE FPDMA QUEUED
00 00 00 00 01 00 00 00 00 00 01 a0 00 01:23:01.930 NOP [Abort queued commands]

Error 35 [2] occurred at disk power-on lifetime: 853 hours (35 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 48 00 03 00 00 00 60 77 91 40 00 at LBA = 0x00607791 = 6322065

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 08 00 00 00 60 77 8c 40 00 01:23:01.910 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 6b ec 40 00 01:23:01.910 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 69 64 40 00 01:23:01.910 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 52 64 40 00 01:23:01.910 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 51 d4 40 00 01:23:01.910 WRITE FPDMA QUEUED

Error 34 [1] occurred at disk power-on lifetime: 853 hours (35 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 48 00 03 00 00 00 60 51 c9 40 00 at LBA = 0x006051c9 = 6312393

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 08 00 00 00 60 51 c4 40 00 01:23:01.890 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 4f 8c 40 00 01:23:01.890 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 4b ec 40 00 01:23:01.890 WRITE FPDMA QUEUED
61 00 20 00 28 00 00 00 60 4b 74 40 00 01:23:01.890 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 4b 64 40 00 01:23:01.890 WRITE FPDMA QUEUED

Error 33 [0] occurred at disk power-on lifetime: 853 hours (35 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 48 00 03 00 00 00 60 2f b1 40 00 at LBA = 0x00602fb1 = 6303665

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 08 00 00 00 60 2f ac 40 00 01:23:01.870 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 2a ac 40 00 01:23:01.870 WRITE FPDMA QUEUED
00 00 00 00 01 00 00 00 00 00 01 a0 00 01:23:01.860 NOP [Abort queued commands]

Error 32 [7] occurred at disk power-on lifetime: 853 hours (35 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 48 00 03 00 00 00 60 2a b1 40 00 at LBA = 0x00602ab1 = 6302385

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 20 00 08 00 00 00 60 2a ac 40 00 01:23:01.840 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 29 64 40 00 01:23:01.840 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 29 2c 40 00 01:23:01.840 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 22 84 40 00 01:23:01.840 WRITE FPDMA QUEUED
61 00 20 00 08 00 00 00 60 1f ac 40 00 01:23:01.840 WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1809 -
# 2 Short offline Completed without error 00% 1809 -
# 3 Extended offline Aborted by host 90% 1809 -
# 4 Short offline Completed without error 00% 1628 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Max Temperature: 39 Celsius
Lifetime Max Temperature: 61 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -4/72 Celsius
Min/Max Temperature Limit: -9/77 Celsius
Temperature History Size (Index): 128 (69)

Index Estimated Time Temperature Celsius
70 2011-10-29 08:15 41 **********************
71 2011-10-29 08:16 41 **********************
72 2011-10-29 08:17 42 ***********************
... ..( 10 skipped). .. ***********************
83 2011-10-29 08:28 42 ***********************
84 2011-10-29 08:29 43 ************************
... ..( 16 skipped). .. ************************
101 2011-10-29 08:46 43 ************************
102 2011-10-29 08:47 44 *************************
... ..( 18 skipped). .. *************************
121 2011-10-29 09:06 44 *************************
122 2011-10-29 09:07 45 **************************
... ..( 35 skipped). .. **************************
30 2011-10-29 09:43 45 **************************
31 2011-10-29 09:44 12 -
32 2011-10-29 09:45 19 -
33 2011-10-29 09:46 26 *******
34 2011-10-29 09:47 29 **********
35 2011-10-29 09:48 32 *************
36 2011-10-29 09:49 34 ***************
37 2011-10-29 09:50 36 *****************
38 2011-10-29 09:51 36 *****************
39 2011-10-29 09:52 37 ******************
40 2011-10-29 09:53 36 *****************
41 2011-10-29 09:54 36 *****************
42 2011-10-29 09:55 37 ******************
... ..( 3 skipped). .. ******************
46 2011-10-29 09:59 37 ******************
47 2011-10-29 10:00 38 *******************
... ..( 2 skipped). .. *******************
50 2011-10-29 10:03 38 *******************
51 2011-10-29 10:04 39 ********************
52 2011-10-29 10:05 26 *******
53 2011-10-29 10:06 26 *******
54 2011-10-29 10:07 27 ********
55 2011-10-29 10:08 28 *********
56 2011-10-29 10:09 28 *********
57 2011-10-29 10:10 28 *********
58 2011-10-29 10:11 29 **********
... ..( 4 skipped). .. **********
63 2011-10-29 10:16 29 **********
64 2011-10-29 10:17 30 ***********
65 2011-10-29 10:18 30 ***********
66 2011-10-29 10:19 31 ************
... ..( 2 skipped). .. ************
69 2011-10-29 10:22 31 ************

Error Write SCT (Get) Error Recovery Control Command failed: scsi error aborted command
Warning: device does not support SCT (Get) Error Recovery Control command

SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
R6S (Bast Castle v1.04 Mod2)
-uragan-
 
Posts: 195
Joined: 16 May 2011, 11:35
Location: Германия

Re: NFS сервер на плеере

Postby Virtual » 29 Oct 2011, 11:27

вроде нашел проблемное место.... разбираюсь ;) спасиб.
а без диска плеер нармально засыпает, и просыпается?
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: NFS сервер на плеере

Postby -uragan- » 29 Oct 2011, 12:00

хорошие новости :)

да, без диска проблем вкл/выкл нет
R6S (Bast Castle v1.04 Mod2)
-uragan-
 
Posts: 195
Joined: 16 May 2011, 11:35
Location: Германия

Re: NFS сервер на плеере

Postby -uragan- » 06 Nov 2011, 21:23

@ Virtual
Благодаря Вам и amp_r6 мой зверек теперь тоже засыпает - огромное спасибо!
R6S (Bast Castle v1.04 Mod2)
-uragan-
 
Posts: 195
Joined: 16 May 2011, 11:35
Location: Германия

PreviousNext

Return to Tips & Tricks

Who is online

Users browsing this forum: No registered users and 11 guests