Восстановление при самой неудачной прошивке Jupiter(1185)

о железе плеера и о периферии

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby lymax » 09 Feb 2015, 15:42

3.3 померить тем же тестером
потом найти RxD - по наличию лога в putty
рядом с ним должен быть TxD - включить аппарат, нажать ESC, должен зайти в ROM Monitor. Ну или для начала просто наличие эха в логе при нажатии кнопок
Марсы: 2*Emtec Movie Cube S800H (amp_r12 vrtn + amp_r12 noGUI[NFS/Samba/FTP/Trans])
Сатурны: Iconbit XDS73D + eGreat R6S Pro (ампс + скин 3Dgui)
+ eGreat R6S Pro (ампс ногуй) + 2*eGreat R6S для тестов
Сеть/Инет: LAN / WLAN 300Mb / ADSL 16Mb
User avatar
lymax
 
Posts: 245
Joined: 12 Jun 2012, 00:10

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby maximen » 09 Feb 2015, 17:02

albelt
Если смотреть на фото слева направо : gnd rx tx
UART Konoos GV4000 | +
md_5fd81c3a.jpg
md_5fd81c3a.jpg (74.95 KiB) Viewed 9194 times

Потом ставь буткод inext_tv_bootloader_other_1185 из темы inext tv
Saturn: iconBIT XDS73d mk2(inext_hd1_225_r0)
Android tv box: Tox1, 2 * X3 Cube
User avatar
maximen
 
Posts: 771
Joined: 21 Feb 2012, 16:07
Location: Донбасс

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby albelt » 12 Feb 2015, 16:33

Подключился к UART Konoos GV4000.
При включении плеера пробегает лог загрузки и останавливается с ошибкой.
На этот лог вообще не обращать внимания?
Проверять утилитой rec.exe и при успехе, затем заливать прошивку с буткодом "inext_tv_bootloader_other_1185" ?
Есть ли смысл сохранить родной буткод?
Привожу лог:

| +
?hello_world!
5528208 0 wawaititEPHY: 8211D
[HDMI]: Set I2C Speed = 50 kHz
[HDMI]: Chk_HotPlug() TV is not connected.
[HDMI]: Read_EDID abort, HDMI cable plug off.
[HDMI]: TV is not connected.
PAL logo

REALTEK ROM Monitor, Revision 0000.0303.0015.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= May 11 2011 21:37:04 /0000.0303.0015
MAC address = 00.11.22.c4.b0.ec
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x78
Endianness = Little
Flash memory size = 512 MByte
SDRAM size = 256 MByte
First free SDRAM address = 0x800a9000

Press 'ESC' to Monitor mode
Linux Kernel:
FW Image from 0xa2020000, to 0x80100000, size=0x415086
Audio FW:
FW Image from 0xa2440000, to 0x81b00000, size=0x1aef00
Video FW:
FW Image from 0xa2600000, to 0x81d80000, size=0x1c62e8
5280Go 5280Go
HDMI Raw Enable: MPG AC3 DTS AAC DDP MLP

SPDIF Raw Enable: MPG AC3 DTS AAC DDP MLP

Force 2ch Format: DTS DTSHD AC3 DDP MLP AAC WMAPRO

Po Power SCOn Music
U_CLK90K=0.012 sec.
go 0x80100000 mtdparts=rtk_nand:365696k,52096k(/),80128k(/usr/local/etc),26368k rootfstype=squashfs root=31:01
Reset Ethernet Mac.


Address = 0x80100000

Realtek LINUX started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 2 UARTs.
System CPU uses external timer interrupt.
Bootloader version: 0000.0303.0015. This version string is of new format.
The information of this board: Company ID:0x0 CPU ID: 0x33 Board ID: 0x303
Ethernet Mac address: 00.11.22.C4.B0.EC
Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x20000000
Linux version 2.6.12.6-VENUS (root@RTMMDMPSA-02.realtek.com.tw) (gcc version 3.4.4 mipssde-6.03.00-20051020) #1 Wed May 4 17:25:43 CST 2011
audio addr: 1b00000
CPU revision is: 00019378
Determined physical RAM map:
memory: 00100000 @ 00000000 (usable)
memory: 00435000 @ 00100000 (reserved)
memory: 015cb000 @ 00535000 (usable)
memory: 00500000 @ 01b00000 (reserved)
memory: 0e000000 @ 02000000 (usable)
show info: max_low_pfn:65536
show info: min_low_pfn:1333
ZONE: DMA, PFN: 0
ZONE: Normal, PFN: 53248
ZONE: DVR, PFN: 4096
Built 1 zonelists
Kernel command line: mtdparts=rtk_nand:365696k,52096k(/),80128k(/usr/local/etc),26368k rootfstype=squashfs root=31:0 1 console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
RBUS DC SYS debug interrupt handler is inserted.
PID hash table entries: 512 (order: 9, 8192 bytes)
Estimate value: CPU frequency 499.52 MHz
Using 27.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 249480k/252716k available (3403k kernel code, 3188k reserved, 628k data, 148k init, 0k highmem)
Warning! Unknown board id.
==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
========== board id: 303 ==========
[INFO] neptune mode...
boot_param value: a0002800
mode: 1
size: 869
color1: 0x808010
color2: 0x808059
color3: 0xc0ffff
color4: 0xad1f
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
pci_scan_single_device, devfun = 0
Read config data (00000000) failed - timeout
pci_scan_single_device, no dev exists
pci_scan_single_device, devfun = 8
pci_scan_single_device, no dev exists
pci_scan_single_device, devfun = 16
pci_scan_single_device, no dev exists




***************** se init module *********************



se init module major number = 254
instcnt=0, u64cnt=0, u64IssuedInstCnt=0
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
[MCP] Info, mcp device detected ...
Hello, Realtek TLB Mapper
AllocBP size: 589824 order: 8
<<<DVR FREE AREA>>>
0: 0
1: 0
2: 0
3: 0
4: 0
5: 0
6: 0
7: 0
8: 1
Addr: 81a00000, order: 8
9: 1
Addr: 81800000, order: 9
10: 0
11: 1
Addr: 81000000, order: 11
12: 11
Addr: 8c000000, order: 12
Addr: 8b000000, order: 12
Addr: 8a000000, order: 12
Addr: 89000000, order: 12
Addr: 88000000, order: 12
Addr: 87000000, order: 12
Addr: 86000000, order: 12
Addr: 8

[Audio Firmware Version] 360747
[Binary src compiled at] May 30 2011 13:39:02

5000000, order: 12
Addr: 84000000, order: 12
Addr: 83000000, order: 12
Addr: 82000000, order: 12
squashfs: version 3.1 (2006/08/19) Phillip Lougher
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
YAFFS Driver Rev:291473 (2010-01-14)
YAFFS Driver is successfully installing.
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize
loop: loaded (max 8 devices)
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2.5-NAPI
e1000e: Copyright(c) 1999 - 2009 Intel Corporation.
this Jupiter eth RX_OFFSET = 0x0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
MAC address = 0x00.11.22.C4.B0.EC
eth0: RTL-8139C+ at 0xb8016000, 00:11:22:c4:b0:ec, IRQ 2
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
VenusSFC MTD init...
NOR flash support list ..
cp_hotplug
(V) MD_WRITE support.
(X) MD_READ support.
(V) HWSEMA support.
(V) AUTO_HW_POLL support.
(X) 4Bytes mode support.
(X) Sfc_delay support.
serial flash inaccessible
physmap flash device: 20000000 at ffd00000
Failed to ioremap
Realtek NAND Flash Driver Rev:349905 (2011-02-10)
power_gpio = 0xb801b11c
power_bits = 16
(V)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(V)NAND_READ_SKIP_UPDATE_BBT
[rtk_nand_read_id] Read ID result as follow
ID0[0xad]
ID1[0xdc]
ID2[0x10]
ID3[0x95]
ID4[0x54]
ID5[0xad]
[rtk_nand_read_id] Read ID result as follow
ID0[0x80]
ID1[0x80]
ID2[0x80]
ID3[0x80]
ID4[0x80]
ID5[0x80]
One HY27UF084G2B chip has 1 die(s) on board
nand part=HY27UF084G2B, id=addc1095, device_size=536870912, chip_size=536870912, num_chips=1, isLastPage=0
[rtk_nand_scan_bbt] have created bbt B0, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
4 cmdlinepart partitions found on MTD device rtk_nand
RTK: using dynamic nand partition
Creating 4 MTD partitions on "rtk_nand":
0x00000000-0x16520000 : "Partition_000"
0x16520000-0x19800000 : "/"
0x19800000-0x1e640000 : "/usr/local/etc"
0x1e640000-0x20000000 : "Partition_003"
0x00000000-0x20000000 : "disc"
Realtek Nand Flash Driver is successfully installing.
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODE: MARS/JUPITER
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
= I2C DELAY : ON
=========================
[I2C1] i2c speed changed to 100 KHz
I2C1 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 1
= MODE: MARS/JUPITER
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
= I2C DELAY : ON
=========================
cec_core_init, register cec_bus 804c9240
mars cec module init
register cec driver 'mars_cec' (804c949c)
register cec device 'mars_cec' (804c93d8) to cec0
probe : cec_dev 'mars_cec' (804c93d8), cec_drv 'mars_cec' (804c949c)
Open Jupiter CEC
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
Realtek Venus Power Management, (c) 2006 Realtek Semiconductor Corp.
cp_open
alloc rings cp->rxdesc_buf =0xa0536000 , cp->ring_dma=0x536000
init_hw

eth0: Set multicast.
jupiter 1g
init_hw finished

eth0: Set multicast.

eth0: Set multicast.
RTK rtc cannot work.

eth0: Set multicast.
IP-Config: Complete:
device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
host=192.168.0.9, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
SCPU_CLK90K=3.914 sec.
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 148k freed
mount: Mounting none on /tmp failed: No such file or directory
Welcome to Realtek Linux

Please press Enter to activate this console. ------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
Starting INET services....
this is 7735R LCD
Lcd Display logo..

[sjg] debug --->> </mnt/GigaView/jet/Linux_Jupiter_QA0104_nand/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_v fd_7735r.c> Lcd_ShowBmp():1284
bmp x=32,y=48,w=96,h=32

[sjg] debug --->> </mnt/GigaView/jet/Linux_Jupiter_QA0104_nand/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_v fd_7735r.c> Lcd_ShowBmp():1285
LCD w=160,h=128

[sjg] debug --->> </mnt/GigaView/jet/Linux_Jupiter_QA0104_nand/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_v fd_7735r.c> Lcd_ShowBmp():1315
bmp x=32,y=48,w=96,h=32
Lcd Init over!
buff write test data=0123456789
------flush priority: 10
flush_page_cache: do flush...
libata version 1.12 loaded.
sata driver initial...2010/11/9 18:00
JUPITER(Ver.C/D): one port supported
mars_init_sata(1295)dev_addr:c00a3660
ata_device_add(4888)probe begin
scsi0 : SATA_DRV
sata dma reset
__mars_sata_phy_reset(881)ap->port_no:0
jupiter mdio setting enable
Realtek Card-Reader Driver Rev:161767 (2011-03-22 11:45)
Realtek SD/MMC Controller Driver is successfully installing.

Running dvdplayer with RootApp
set corepath: /tmp/hdd/volumes/HDD1/
RootApp AVHDD version...

eth0: Set multicast.
enter 2nd case...
================================================
================================================
root execute DvdPlayer...
================================================
================================================
sata1: reset phy again!
sata phy reset
IN : /tmp/ramfs/smb
downloader 0 starts, 0x17d25b8
downloader 1 starts, 0x17d46b0
MusicTVAP, MusicTVAP.cpp:44
[Dlna DMR] this is GDlnaMediaRendererAP
CMD: mkdir -p /tmp/netb/smb
CMD: mkdir -p /tmp/smb
CMD: ifconfig > /tmp/netb/samba_my_ip
Warning!! the Mask is 255.0.0.0.
!!!BootUP!!!






WARNING WARNING WARNING m_db_manage_flag_cnt = -1





DB FILENAME = /tmp/ramfs/Setup
[DataObject.cpp 550] ---- Create new DB Start -/usr/local/etc/dvdplayer/Setup----
[DataObject.cpp 669] database compact ok!!
[DataObject.cpp 575] ---- Create new DB End -----
[DataObject.cpp 440]DB Develop Version same . Don't be upgrade.
[DataObject.cpp 479]DB Version same . Don't be upgrade.



m_BookMark_Size=4096 m_Signature_Size=16


[DataObject.cpp 1355] SQL ERROR 8 : attempt to write a readonly database
[DataObject.cpp,1429] error : 8 ,attempt to write a readonly database SQL :PRAGMA default_cache_size = 650;
[DataObject.cpp 1355] SQL ERROR 8 : attempt to write a readonly database
[DataObject.cpp,1429] error : 8 ,attempt to write a readonly database SQL :PRAGMA default_cache_size = 650;
WatchDog does not receive signal for 2 seconds, value: 0
org change count = 0 , total change count = 320
Bootup t1 = 2061837145.491 sec
Bootup t2 = 2061***256MB version...
837145.518 sec
pli initialization...
Memory address 0x40000000
Bootup t3 = 2061837145.527 sec
--- RtkBootUP(81): 10.854 sec
***************** se open: queue = 0 *********************
***************** se open: initialized = 0 *********************
arch/mips/realtek-boards/drivers/se.c, 614: offset = 0, se_devices = 8d038000
arch/mips/realtek-boards/drivers/se.c, 624: offset = 0
arch/mips/realtek-boards/drivers/se.c, 668: length = 20480
arch/mips/realtek-boards/drivers/se.c, 669: offset = 218333184
arch/mips/realtek-boards/drivers/se.c, 676: offset = 218333184
arch/mips/realtek-boards/drivers/se.c, 614: offset = 98316, se_devices = 8d038000
arch/mips/realtek-boards/drivers/se.c, 624: offset = 402702336
arch/mips/realtek-boards/drivers/se.c, 668: length = 4096
arch/mips/realtek-boards/drivers/se.c, 669: offset = 402702336
arch/mips/realtek-boards/drivers/se.c, 676: offset = 402702336
start[0-3] = {7001a500, 7001a504, 7001a508, 7001a50c}
end[0-3] = {7001a510, 7001a514, 7001a518, 7001a51c}
+++ ALLOC index: 2048 order: 9
1. start remap DVR zone 81800000(80567000) 512...
map_done is 512...
+++ ALLOC index: 2560 order: 7
1. start remap DVR zone 81a00000(8056b000) 128...
map_done is 128...
Video DebugMem PVIDEO_RPC_SetDebugMemory Called!+++ ALLOC index: 2688 order: 7
hysical Address 1. start remap DVR zone 81a80000(8056c000) 128...
= 0xd945800
map_done is 128...
+++ ALLOC index: 0 order: 8
1. start remap DVR zone 81000000(80557000) 256...
map_done is 256...
[AUDIO WARNING]
no more memory , do Remote Malloc. Size 0x00186008
766 loadThemeSetting resource.cpp
No THEMESET_INI exists
-=- create FT engine for ./Resource/font/hebrew.ttf
[VoutUtil.cpp:1~~SetVideoStandard: fmt 28 ped 1 prog 1
33,SetVideoStandard] 1, standard = 28
[VoutUtil.cpp:134,Set
(TVE) TVE_DAC_mode 0!! ~~comp 0, ch2 1
~~TVE standard#
VideoStandard] 2, enProg = 1 +++ ALLOC index: 512 order: 9

[VoutUtil.cp1. start remap DVR zone 81200000(8055b000) 512...
p:135,SetVideoStWARNING[2]:TVE p-underflow @ line 0
WARNING[2]:TVE h-underflow @ line 273
andard] 3, enDIF = 1
[VoutUtil.cpp:136,SetVideoStandard] 4, enCompRGB = 0
[VoutUtil.cpp:137,SetVideoWARNING[2]:TVE i-underflow @ line 0
Standard] 5, pedType = 1
[VoutUtil.cpp:138,SetVideoStandard] 6, dataInt0 = 4
[VoutUtil.cpp:139,SetVideoStandard] 7, dataInt1 = 0
map_done is 512...
[AUDIO WARNING]
no more memory , do Remote Malloc. Size 0x00186008
+++ ALLOC index: 45056 order: 12
1. start remap DVR zone 8c000000(806b7000) 4096...
map_done is 0...
===============
====Lcd===========
===============
abstractap semid=0
sata1: reset phy again!
sata phy reset
+++ ALLOC index: 1024 order: 9
1. start remap DVR zone 81400000(8055f000) 512...
map_done is 512...
-------------------
Audio Version = 360747 (jupiter)
Common Version = 355565
Build Date = May 30 2011
Build Time = 13:39:02
Note =
-------------------
ClassifyBonding 0x00000302, num = 0x00000005 (DD)
semctl ret=0[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Jupiter
[DataObject.cpp 1355] SQL ERROR 8 : attempt to write a readonly database
[DataObject.cpp,1429] error : 8 ,attempt to write a readonly database SQL :PRAGMA default_cache_size = 650;
[HDMI]: AP set setHDMIDeepColorMode=0 do nothing.
[HDMI]: getHDMIPlugged()=-1
[HDMI]: getHDMIReady()=0
[HDMI]: getHDMISwitchTVSystem()=0
[HDMI]: Turn on HDMI AUDIO
[HDMI]: Send_AudioMute AP_SETUP_HDMI_MUTE=0 Select=2 PS=0
[HDMI]: AP_SETUP_HDMI_MUTE=0
[HDMI]: Clear HDMI Audio Mute(Turn on AUDIO)
GrandMa Revision: 358218
[HDMI]: Send_Aud[I2C0] i2c speed changed to 50 KHz
ioMute() Ok, argp.hdmi_mute=0
[HDMI]: JUPITER HDMI is running...
[HDMI]: Disable HDCP
[HDMI]: Disable YST Mode. YSTMode_cnt=1
[HDMI]: USE_HDthis is 7735R LCD
CP=NO in MakeCon fig, do not Enable HDCP
[HDMI]: Set I2C Speed = 50 kHz
try - /dev/i2c/0
[HDMI]: Rx status = 0
[HDMI]: Hotplug Change !!! -1 -> 0 => No HDMI
[HDMI]: Turn off HDMI VIDEO
[HDMI]: Turn off HDMI VIDEO
[HDMI]: Turn off HDMI VIDEO OK
check OK .....

[sjg] debug --->> <LCD_L.cpp> VFD_Controller():1035
mmap addr=2af48000,size =0000a000,read test data = 0123456789
<5>
eth0: Set multicast.
WatchDog does not receive signal for 2 seconds, value: 0
Lcd Display logo..

[sjg] debug --->> </mnt/GigaView/jet/Linux_Jupiter_QA0104_nand/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_v fd_7735r.c> Lcd_ShowBmp():1284
bmp x=32,y=48,w=96,h=32

[sjg] debug --->> </mnt/GigaView/jet/Linux_Jupiter_QA0104_nand/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_v fd_7735r.c> Lcd_ShowBmp():1285
LCD w=160,h=128

[sjg] debug --->> </mnt/GigaView/jet/Linux_Jupiter_QA0104_nand/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_v fd_7735r.c> Lcd_ShowBmp():1315
bmp x=32,y=48,w=96,h=32

[sjg] debug --->> <LCD_L.cpp> Lcd_Init():885
VfdStatus.status=00000001

[sjg] debug --->> <LCD_L.cpp> Get_Lcd_Parm():844
McuChipID=2
LcdChipID=0
Screen_dir=3
H_size=160
V_size=128
BytesPerpixel=2
color_format=1

[sjg] debug --->> <LCD_L.cpp> Lcd_Init():899



lcd init over!!!!!!!!!!!!!!!

file system 3, cylinder 0
mount to /tmp/hdd/volumes/HDD1
file system 1, cylinder 0
mount to na
file system 2, cylinder 0
mount to /tmp/hdd/root
checked magic number = -901340672
я



[Video Firmware Version] 357678
[Video Binary Built on] May 4 2011 17:49:21
+++ ALLOC index: 40960 order: 12
1. start remap DVR zone 8b000000(80697000) 4096...
map_done is 184...
+++ ALLOC index: 36864 order: 10
1. start remap DVR zone 8a000000(80677000) 1024...
map_done is 183...
+++ ALLOC index: 37888 order: 10
1. start remap DVR zone 8a400000(8067f000) 1024...
map_done is 183...
+++ ALLOC index: 256 order: 3
1. start remap DVR zone 81100000(80559000) 8...
map_done is 8...
+++ ALLOC index: 32768 order: 12
1. start remap DVR zone 89000000(80657000) 4096...
map_done is 0...
+++ ALLOC index: 28672 order: 12
1. start remap DVR zone 88000000(80637000) 4096...
map_done is 0...
VBM: configured to SD!
[BONDING] ac3_dts_ddp dec= 0x00000000
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key = 0x00000001 (1 : has, 0: no key)
[BONDING] MLP ret= 0x00000000, key= 0x00000000, HBR= 0x00000001, dac= 0x00000000
dac's key = 0x00000000 (1 : has, 0: no key)
[BONDING] MLP ret= 0xffffffff, key= 0x00000000, HBR= 0x00000001, dac= 0x00000001
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (1,0,0)
Do you have key?(0 = no!) 0
Bonding option process 0x00000009 to AUDIO_UNKNOWN_TYPE !!!
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key = 0x00000001 (1 : has, 0: no key)
[BONDING] DTSHD ret= 0x00010000, getkey= 0x00000000, HBR = 0x00000001, dac= 0x00000000dac's key = 0x00000001 (1 : has, 0: no key)
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process 0x0000001b to AUDIO_UNKNOWN_TYPE !!!
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process 0x0000001c to AUDIO_UNKNOWN_TYPE !!!
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process 0x0000001d to AUDIO_UNKNOWN_TYPE !!!
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,0,1)
Do you have key?(0 = no!) 0
Bonding option process 0x00000023 to AUDIO_UNKNOWN_TYPE !!!
High = 0x00000000, Low = 0x43c1b4fe
The following Format is supported:
MPEG
AC3
LPCM
DTS
WMA
AAC
VORBIS
DDP {AC3+, EAC3}
WMA Pro
MP4 LC-AAC
MP4 HE-AAC
RAW AAC
ADPCM
FLAC
A Law PCM
u Law PCM
AMR
[VIDEO Capability]HighWord 0xffffffff, LowWord 0xffffffff
[DataObject.cpp 1355] SQL ERROR 8 : attempt to write a readonly database
[DataObject.cpp,1429] error : 8 ,attempt to write a readonly database SQL :PRAGMA default_cache_size = 650;
[AbstractAP.cpp:1684:Init].SetAudioDolbyCompressMode(COMPRESS_LINEOUT)
###### - script pParam: rss_file://./setup_menu/scripts/init.rss
############### m_bIsActivate = 1
[DrawBitmap.cpp:306] bitmap header read fail....................
create image [./setup_menu/scripts/] error!!!
[DrawBitmap.cpp:306] bitmap header read fail....................
create image [./setup_menu/scripts/] error!!!
[Script] page title is $[INIT_SETUP]
[Script] init.rss zhu_31
___chenal for audio 0326___[SetAudioMute] AudioUtil.cpp 282______
[IMSAP.cpp][Activate][1466]: Create loadmedia thread done
IN : /tmp/net
Create /tmp/net Ok!!!
board_dac_mute--board.cpp--55-------chenal 0326-for mute----
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
Error! Not legal char!!!!!
WatchDog does not receive signal for 2 seconds, value: 0
[IMSAP.cpp][threadLoadMedia][1547]: Wait for condition variable
[DataObject.cpp 1355] SQL ERROR 8 : attempt to write a readonly database
[DataObject.cpp,1429] error : 8 ,attempt to write a readonly database SQL :PRAGMA default_cache_size = 650;
[DataObject.cpp 1355] SQL ERROR 8 : attempt to write a readonly database
[DataObject.cpp,1429] error : 8 ,attempt to write a reado_page_fault() #2: sending SIGSEGV to MAIN for invalid read access from
00000034 (epc == 2aef9950, ra == 00d0a940)
donly database Scurrent context: 253
QL :PRAGMA defaudvr_asid: 0x53
lt_cache_size = ########## User stack address: 81153000
650;
no devcertPage flags: 61000070, index: 522901, count: 0, mapcount: 0
file exists. Crsending signal: 11
eate dummy one!!Call Trace:!!

[<80149410>] force_sig_info+0x54/0x154
[<8011ef08>] do_page_fault+0x3b8/0x450
[<8011eccc>] do_page_fault+0x17c/0x450
[<8019e844>] filp_open+0x30/0x270
[<802d073c>] add_timer_randomness+0x148/0x184
[<8019ebac>] get_unused_fd+0x128/0x1f8
[<8016572c>] __do_IRQ+0x210/0x2a4
[<8019ee6c>] sys_open+0x104/0x144
[<8019ee40>] sys_open+0xd8/0x144
[<8011f470>] tlb_do_page_fault_0+0xf8/0x100
[<8011caec>] stack_done+0x20/0x40

pli initialization...
clear pli setting....
se release, count = 0
CPU 0 Unable to handle kernel paging request at virtual address c005e058, epc == c0084528, ra == 801656c0
Oops in arch/mips/mm/fault.c::do_page_fault, line 229[#1]:
Cpu 0
$ 0 : 00000000 00000001 c005e058 c005d000
$ 4 : 00007800 c008b240 00000000 80516d80
$ 8 : 10007f00 1000001f 804b0000 804b0000
$12 : ffffffff 00000002 00000001 8deddbf0
$16 : 8d840e60 00004000 00000000 00000003
$20 : c0090000 8d01aee0 8deddc58 8deddf30
$24 : 80518dd7 803a7ab4
$28 : 8dedc000 8deddbd8 7cbffb08 801656c0
Hi : 000000a6
Lo : 4c366000
epc : c0084528 VFD_interrupt_handler+0x45c/0x4e4 [venus_vfd_7735r] Not tainted
ra : 801656c0 __do_IRQ+0x1a4/0x2a4
Status: 10007702 KERNEL EXL
Cause : 48808008
BadVA : c005e058
PrId : 00019378
Modules linked in: rtk_sd mmc_block sata_mars mmc_core libata venus_vfd_7735r
Process ExtHddScanUtil (pid: 262, threadinfo=8dedc000, task=8deaabf8)
Stack : 8d678d20 804f0060 8d678d20 804f0060 00000000 00000003 8d840e60 804f0060
00000000 00000003 00000000 801656c0 00000001 8deddbf0 80520000 00000003
80520000 00000003 00000800 00000001 8def85a4 00000009 8dedde80 80114208
805189ec 80520000 58808800 10007f03 58808800 10007f03 80101084 000000a6
4c366000 804b0000 58808800 80139270 00000000 00000001 00000000 00000001
...
Call Trace:
[<801656c0>] __do_IRQ+0x1a4/0x2a4
[<80114208>] do_IRQ+0xd8/0x19c
[<80101084>] mipsIRQ+0x124/0x140
[<80139270>] release_console_sem+0x574/0x708
[<803a7ab4>] sock_destroy_inode+0x0/0x10
[<801c6ef4>] dput+0x2c/0x330
[<8019181c>] __vunmap+0xa4/0x200
[<801918b0>] __vunmap+0x138/0x200
[<801ca6b8>] clear_inode+0x14/0xd0
[<c0090000>] ata_pio_task+0x84/0x888 [libata]
[<c0084e4c>] VfdBuff_mmap_free+0xc0/0xe4 [venus_vfd_7735r]
[<801c6ef4>] dput+0x2c/0x330
[<c0084e88>] venus_vfd_vfdo_release+0x18/0x28 [venus_vfd_7735r]
[<801a1274>] __fput+0x68/0x36c
[<801a1274>] __fput+0x68/0x36c
[<8019ef30>] filp_close+0x78/0x23c
[<8019f0d8>] filp_close+0x220/0x23c
[<8013b1dc>] put_files_struct+0x170/0x200
[<8013c214>] do_exit+0x1ac/0x1028
[<8013c260>] do_exit+0x1f8/0x1028
[<8013d1b8>] sys_exit_group+0x0/0xc
[<8014b8dc>] get_signal_to_deliver+0x644/0x6ac
[<801176dc>] do_signal+0x80/0x2c8
[<80134a30>] __mmdrop+0x2c/0x48
[<8044caa4>] schedule+0xacc/0xce8
[<8044dfa8>] schedule_timeout+0xac/0x1bc
[<80147294>] process_timeout+0x0/0x8
[<801473b8>] sys_nanosleep+0x110/0x21c
[<8013f948>] sys_gettimeofday+0x24/0xb0
[<80112de0>] work_notifysig+0x10/0x18


Code: 8ca30014 00021080 00431021 <8c430000> 3c02c009 8c42b298 ac430000 8ca40004 8ca20008
eth0 Regs : 0xb8016000
00 11 22 c4 b0 ec 00 00 00 00 00 80 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 02 00 00 00 02 03 f5 00 00
00 00 0c 00 00 00 00 2e 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 ec 00 00 00 84 01 79 49
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
eth0 Regs : 0xb8016100
a0 53 68 00 00 00 00 00 00 00 00 00 00 00 00 00
e0 cf fd 3c 00 00 00 00 00 00 00 00 00 00 00 00
43 09 3e 5c 00 00 00 00 00 00 00 00 00 00 00 00
21 a7 62 c4 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0 53 60 00 00 00 7f 00 00 00 00 00 dd d3 5e 7d
eth0 Regs : 0xb8016200
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
7f 10 20 00 40 08 00 30 00 00 00 00 00 00 00 4b
00 00 00 00 00 00 00 00 00 00 00 00 00 05 20 80
00 00 00 00 00 00 00 00 00 00 01 1a 00 00 00 0f
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
eth0 RxFDP : 0xa0536000
00 08 00 80 10 d0 5f 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 5f 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 5f 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 60 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 64 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 65 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 66 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 67 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 68 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 f0 69 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 20 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 30 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 40 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 50 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 60 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 70 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 80 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 90 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 a0 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 b0 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 c0 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 d0 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 e0 6a 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 00 6b 0d 00 00 00 00 00 00 00 00
00 08 00 80 10 10 6b 0d 00 00 00 00 00 00 00 00
00 08 00 c0 10 20 6b 0d 00 00 00 00 00 00 00 00
Kernel panic - not syncing: Aiee, killing interrupt handler
Dr.HD XS300i (Realtek RTD1073DD) AMP_r12
Konoos MS-500(Realtek RTD1073DD)AMP_r12
Konoos GV-4000(Realtek RTD1185DD)GV4000_MOS
MoS3, router Dlink 808
albelt
 
Posts: 45
Joined: 08 Mar 2013, 22:04

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby Virtual » 12 Feb 2015, 17:01

зачем те бут шить? он живой.
прошей прошивку "через кнопку"
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby albelt » 12 Feb 2015, 17:14

Нету кнопок на этом плеере...
Dr.HD XS300i (Realtek RTD1073DD) AMP_r12
Konoos MS-500(Realtek RTD1073DD)AMP_r12
Konoos GV-4000(Realtek RTD1185DD)GV4000_MOS
MoS3, router Dlink 808
albelt
 
Posts: 45
Joined: 08 Mar 2013, 22:04

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby Virtual » 12 Feb 2015, 17:25

есть еще softreset :mrgreen:
так же есть erase -m из Realnek Monitor

PS а кнопочка должна быть! может ее просто не нашли?
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby maximen » 13 Feb 2015, 00:05

albelt
Кнопка на твоём плеере не распаяна, но контакты для неё должны быть... буткод обновлять только если хочешь использовать прошивки iNeXT TV moS
Saturn: iconBIT XDS73d mk2(inext_hd1_225_r0)
Android tv box: Tox1, 2 * X3 Cube
User avatar
maximen
 
Posts: 771
Joined: 21 Feb 2012, 16:07
Location: Донбасс

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby albelt » 13 Feb 2015, 15:56

Спасибо большое всем за советы и помощь.

Прошился через USB-TTL, через Realtek Monitor командой "erase -m", затем "reset", с USB флешки, прошивкой GV4000_MOS
Все прошло штатно - плеер ожил, выкинул меню первичных настроек на LCD монитор.
Что интересно - теперь стало нормально работать отключение в Standby mode и последующий "выход из спячки" при включении с пульта.
Ранее, после перехода с заводской прошивки на GV4000_MOS, плеер невозможно было "разбудить" после перехода в Standby - приходилось "довыключать" пультом до красного светодиода и включать снова.

Теперь встала задача выбрать лучшую прошивку из имеющихся в наличии:
f_m_gv4000, gv4000_max_mod, inext_tv. Буду рыть форум.

Еще раз спасибо всем.
Dr.HD XS300i (Realtek RTD1073DD) AMP_r12
Konoos MS-500(Realtek RTD1073DD)AMP_r12
Konoos GV-4000(Realtek RTD1185DD)GV4000_MOS
MoS3, router Dlink 808
albelt
 
Posts: 45
Joined: 08 Mar 2013, 22:04

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby maximen » 14 Feb 2015, 03:21

Если надумашь сменить буткод, настоятельно рекомендую сделать копию нулевого блока, читай тему как сохранить оригинальный бут-код viewtopic.php?f=14&t=3503 , этот файл пригодится многим
Saturn: iconBIT XDS73d mk2(inext_hd1_225_r0)
Android tv box: Tox1, 2 * X3 Cube
User avatar
maximen
 
Posts: 771
Joined: 21 Feb 2012, 16:07
Location: Донбасс

Re: восстановление при самой неудачной прошивке Jupiter (118

Postby Garry627 » 17 Apr 2015, 19:08

В результате неудачной прошивки плеера пришлось переместиться на эту ветку. Сделал снимки платы для консультации - куда здесь коннектиться шнурком? На плате нет обозначенного производителем разъёма UART, к которому после прочтения некоторого количества материала на форуме я должен подключиться. Есть пустой разъем, но на нем не 6 и не 4 пина, как обычно бывает на UART, а 5, центральный контакт у него похоже на "земле" платы сидит. На оборотной стороне есть нераспаянные контакты 2 разъемов - двухрядного 8-пинового и однорядного 6-пинового. Вот последний мне и представляется как претендент на подключение, крайний правый контакт его звонится, да и так видно - Gnd (общий, минус, земля), на остальных контактах тестер показывает, что болтается потенциал около +3.3 Вольта. Прошу специалистов опытным глазом оценить - прав я или нет в отношении этого претендента на звание "UART"? От него дорожки уходят под чип 1185. Обычно разьем где-то на перифирии платы стоит у других плат, как я выяснил при изучении форума. Опять же может так быть, что между чипом 1185 и ножками разъема нет никакой буферной микросхемы? Жду совета бывалых людей - куда цеплять?
| +
1.JPG
Лицевая сторона платы
1.JPG (231.07 KiB) Viewed 8631 times
2.JPG
Обратная сторона
2.JPG (166.03 KiB) Viewed 8631 times
3.JPG
Нераспаянные разъемы - 6-пиновый - это то что нужно для подключения?
3.JPG (179.28 KiB) Viewed 8631 times
Measy E8HDL xfw_XDS42GL_XDS52GL_v9.5.2.r7725_(08.09.12)_2.02_RU
Garry627
 
Posts: 8
Joined: 13 Apr 2015, 08:52
Location: РК, Алма-Ата

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 28 guests

cron