Зависания служб и некорректная работа ПО на Iconbit XDS1003D

Разбор непоняток

Зависания служб и некорректная работа ПО на Iconbit XDS1003D

Postby cybernetik » 17 Nov 2017, 04:01

Здравствуйте.
Где-то около полутора лет назад начали наблюдаться проблемы в работе плеера Iconbit XDS1003D приобретенного в ноябре 2011 года, и работающего с тех пор 24/7.
Бутлоадер KIIE.0402.1067, прошивка Mede8er X3D_Series_V4.0.2b160406, MOS обновлен до упора.

С определенного момента начала наглухо зависать Samba из MOS при запуске плеера. Отключил её, использую прошивочную.
+ Затем добавился ещё один симптом - стало отваливатся управление плеером с пульта через несколько секунд после загрузки плеера. По сети плеер остается доступным.
Перезагрузка в этом случае обычно не помогает, управление после перезагрузки снова отваливается, помогает только отключение плеера на несколько секунд.
+ В прошивке по неизвестной причине не скачивается и не обновляется скрейпер.
Пробовал откатывать прошивки на более старые версии - проблемы сохраняются.

Дополнительные симптомы из логов:
Во флеше 2 битых блока.
cat /proc/nandinfo | +
~ # cat /proc/nandinfo
nand_PartNum:H27UAG8T2B
nand_size:2147483648
chip_size:2147483648
block_size:2097152
page_size:8192
oob_size:448
ppb:256
RBA:51
BBs:2

/bin/df -h | +
/bin/df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 110.6M 110.6M 0 100% /
devtmpfs 228.9M 0 228.9M 0% /dev
/dev/mtdblock2 1.7G 59.7M 1.7G 3% /usr/local/etc
/dev/ram0 40.0K 40.0K 0 100% /mnt/rd
/dev/root 110.6M 110.6M 0 100% /sys/realtek_boards/AES_CCMP
/dev/root 110.6M 110.6M 0 100% /sys/realtek_boards/modelconfig
/dev/sda1 3.6T 3.6T 16.4G 100% /tmp/usbmounts/sda1

Больше всего смущает это:
/sbin/fdisk -l | +
/sbin/fdisk -l
Disk /dev/mtdblock0: 75 MB, 75497472 bytes
255 heads, 63 sectors/track, 9 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Disk /dev/mtdblock0 doesn't contain a valid partition table

Disk /dev/mtdblockdisc: 56 MB, 56623104 bytes
255 heads, 63 sectors/track, 6 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Disk /dev/mtdblockdisc doesn't contain a valid partition table

Disk /dev/sda: 2199.0 GB, 2199023255040 bytes
255 heads, 63 sectors/track, 267349 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot Start End Blocks Id System
/dev/sda1 1 267350 2147483647+ ee EFI GPT

И это:
/sbin/parted -l | +
/sbin/parted -l
Model: ATA ST4000DM000-1F21 (scsi)
Disk /dev/sda: 4001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt

Number Start End Size File system Name Flags
1 1049kB 4001GB 4001GB
2 4001GB 4001GB 133MB

Error: /dev/mtdblock0: unrecognised disk label

Error: /dev/mtdblock1: unrecognised disk label

Error: /dev/mtdblock2: unrecognised disk label

Error: /dev/mtdblock3: unrecognised disk label

Error: /dev/mtdblockdisc: unrecognised disk label

Лог загрузки плеера:
/bin/dmesg | +
/bin/dmesg
Linux version 2.6.34-VENUS (rob_luo@dmp193) (gcc version 4.3.6 20110218 (prerelease) (GCC) ) #4 PREEMPT Thu Dec 27 11:05:59 CST 2012

Realtek LINUX started...
Venus setting:
ROSs have 4194304 bytes RAM.
System CPU has 1 UART.
System CPU uses internal timer interrupt.
Bootloader version: KIIE.0402.1067. This version string is of new format.
The information of this board: Company ID:0x0 CPU ID: 0x4 Board ID: 0x402
Ethernet Mac address: 00.CE.39.B4.C6.6F
Model Config length=3
Base year of RTC is 2010.
audio addr: 1b00000
Config serial console: console=ttyS0,115200n8r
bootconsole [early0] enabled
CPU revision is: 00019385 (MIPS 24Kc)
FPU revision is: 01739300
Determined physical RAM map:
memory: 00100000 @ 00000000 (reserved)
memory: 01a00000 @ 00100000 (usable)
memory: 00500000 @ 01b00000 (reserved)
memory: 0e000000 @ 02000000 (usable)
memory: 00100000 @ 10000000 (reserved)
memory: 07f00000 @ 10100000 (usable)
memory: 00100000 @ 18000000 (reserved)
memory: 05b00000 @ 18100000 (usable)
Wasting 8192 bytes for tracking 256 unused pages
Zone PFN ranges:
DMA 0x00000000 -> 0x00002000
Normal 0x00002000 -> 0x0001dc00
Movable zone start PFN for each node
Node 0: 23552
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x0001dc00
On node 0 totalpages: 121856
free_area_init_node: node 0, pgdat 8066bf70, node_mem_map 806df000
zone DMA size: 2000 realsize: 2000
DMA zone: 0 pages reserved
DMA zone: 8192 pages, LIFO batch:1
zone Normal size: 3c00 realsize: 3c00
Normal zone: 15360 pages, LIFO batch:3
zone Movable size: 18000 realsize: 18000
Movable zone: 98304 pages, LIFO batch:31
zonelist: Movable Normal DMA
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 121856
Kernel command line: mtdparts=rtk_nand:73728k,114688k(/),1800192k(/usr/local/etc),108544k rootfstype=squashfs root=31:01 console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00077e21
Readback ErrCtl register=00077e21
Memory: 468736k/479232k available (4385k kernel code, 10496k reserved, 1171k data, 184k init, 0k highmem)
Disable zone Movable
hole addr: 65536 size: 256
hole addr: 98304 size: 256
*****reserve DVR zone...
NR_IRQS:8
Estimated CPU frequency: 756.03 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 502.98 BogoMIPS (lpj=2514944)
Mount-cache hash table entries: 512
devtmpfs: initialized
NET: Registered protocol family 16
prom_flashsize = 0x80000000
Flash size is 0x2000000
registering PCI controller with io_map_base unset
bio: create slab at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.22.1.
[PCI] CFG WARNING,Read config data ((null)) failed - timeout
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource MIPS-DMP
NET: Registered protocol family 2
Switched to NOHz mode on CPU #0
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 32




***************** se init module *********************



se init module major number = 253
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
[user land] CmdBuf virt addr = 9d904000/bd904000, phy addr=1d904000
[MCP] Info, mcp device detected ...
init_vdso successfull
rtktlb: Hello, Realtek TLB Mapper...
AllocBP size: 1277952 order: 9 offset: 8192
<<>>
0: 0
1: 0
2: 0
3: 0
4: 0
5: 0
6: 0
7: 0
8: 2
Addr: 90100000, order: 8
Addr: 98100000, order: 8
9: 2
Addr: 90200000, order: 9
Addr: 98200000, order: 9
10: 2
Addr: 90400000, order: 10
Addr: 98400000, order: 10
11: 2
Addr: 90800000, order: 11
Addr: 98800000, order: 11
12: 2
Addr: 91000000, order: 12
Addr: 99000000, order: 12
13: 2
Addr: 82000000, order: 13
Addr: 92000000, order: 13
14: 4
Addr: 84000000, order: 14
Addr: 88000000, order: 14
Addr: 8c000000, order: 14
Addr: 94000000, order: 14
squashfs: version 4.0 (2009/01/31) Phillip Lougher
insert mtpfs module OK
NTFS driver 2.1.29 [Flags: R/O].
YAFFS Driver Rev:329787 (2010-10-05)
yaffs built Dec 27 2012 11:05:28 Installing.
YAFFS Driver is successfully installing.
msgmni has been set to 915
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
console [ttyS0] enabled, bootconsole disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Realtek NAND Flash Driver Rev:337905 (2010-10-18)
(X)Enable interrupt mechanism of NAND driver.
Get parameter from register...
[rtk_nand_init]Bootcode size 0x3200000
[rtk_nand_init]Factory parameter size 0x400000
[rtk_nand_init]Disable NFCP...
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
READ ID:0xad 0xd5 0x94 0x9a 0x74 0x42
One H27UAG8T2B chip has 1 die(s) on board
nand part=H27UAG8T2B, id=add5949a, device_size=2147483648, chip_size=2147483648, num_chips=1, page_size=8192, isLastPage=1, eccBits=24
[rtk_nand_scan_bbt] have created bbt B1, just loads it !!
[dump_BBT] Nand BBT Content
[0] (0, 25, 0, 1023)
[1] (0, 26, 0, 1022)
4 cmdlinepart partitions found on MTD device rtk_nand
RTK: using dynamic nand partition
Creating 4 MTD partitions on "rtk_nand":
0x000000000000-0x000004800000 : "Partition_000"
0x000004800000-0x00000b800000 : "/"
0x00000b800000-0x000079600000 : "/usr/local/etc"
0x000079600000-0x000080000000 : "Partition_003"
0x000000000000-0x000080000000 : "disc"
[rtk_nand_init]Ecc bit select 24
Realtek Nand Flash Driver is successfully installing.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
this Jupiter eth RX_OFFSET = 0x0
MAC address = 0x00.CE.39.B4.C6.6F
eth0: RTL-8139C+ at 0xb8016000, 00:ce:39:b4:c6:6f, IRQ 2
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
Initializing USB MTP/PTP driver...
usbcore: registered new interface driver usb-mtp
USB MTP/PTP support registered.
mice: PS/2 mouse device common for all mice
rtc-rtk_dmp_venus rtc-rtk_dmp_venus.0: rtc core: registered rtc-rtk_dmp_venus as rtc0
rtc: Real Time Clock of Realtek DMP's Venus series CPUs
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
[I2C1] i2c speed changed to 100 KHz
I2C1 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 1
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.1.0)
cec_core_init, register cec_bus 806640a0
saturn cec module init
register cec driver 'mars_cec' (80664160)
register cec device 'mars_cec' (806641d0) to cec0
probe : cec_dev 'mars_cec' (806641d0), cec_drv 'mars_cec' (80664160)
Open Mars CEC
cp_hotplug
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
#0: Mars 1
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
<<<<< Enable memory protector >>>>>
rtk_enable_kcpu : Code Size = 6888 , Data Size = 2456
Saturn_Param_PWM_Irda_Key.protocol = 0
Saturn_Param_PWM_Irda_Key.power_key = 0xff00fc03
Saturn_Param_PWM_Irda_Key.eject_key = 0xe817fc03
Saturn_Param_PWM_GPIO_Key.power_key_number = -1
Saturn_Param_PWM_GPIO_Key.eject_key_number = -1
_sleeptext = 0x80546bfc , _esleeptext = 0x805486e4
_sleepdata = 0x8066ca80 , _esleepdata = 0x8066d418
Realtek Saturn Power Management, (c) 2011 Realtek Semiconductor Corp.
avcpu: audio & video cpu driver for Realtek Media Processors
cp_open
init_hw

eth0: Set multicast.
jupiter/saturn 1g
init_hw finished

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.
ADDRCONF(NETDEV_UP): eth0: link is not ready
IP-Config: Complete:
device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
host=192.168.0.9, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
devtmpfs: mounted
Freeing unused kernel memory: 184k freed
Venus rtc can work.
yaffs: dev is 32505858 name is "mtdblock2" rw
yaffs: passed flags ""
yaffs: Attempting MTD mount of 31.2,"mtdblock2"
yaffs: auto selecting yaffs2
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
Adding 28k swap on /mnt/rd/swap.img. Priority:-1 extents:1 across:28k
venus_ir_new: module_layout: kernel tainted.
Disabling lock debugging due to kernel taint
Old VenusIR driver found at 80642b50
Found venus_ir_cleanup_module() @ 0x8010fa9c
venus_ir_cleanup_module() called
New Venus IR driver loaded
hotplug eth0: link up, 100Mbps, full-duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

eth0: Set multicast.
rtksdio: 0xb800036c = 0x555d4844
Realtek Card-Reader Driver Rev:SATURN (2012-02-08 13:50)
rtksdio: power_gpio = 0xb801b110
rtksdio: power_bits = 31
rtksdio: clk change to 15MHz
mmc0: rtksdio driver initialized,
Realtek Card-Reader Controller Driver is successfully installing.

*** 476MB version...
auth: memory address 0x40000000...
clear pli setting....
save exit: isCheckpointed 1
*****check animation logo...
=====video is ready...
=====audio is ready...
Enable zone Movable
*** 476MB version...
auth: memory address 0x40000000...
pli malloc order: 2
+++ ALLOC index: 57600 order: 2
zone: 8071f000 page: 808e1000(90100000) count: 4
start remap DVR zone 90100000(808e1000) 4...
total migrated: done: 0 fail: 0
***************** se open: queue = 0 *********************
***************** se open: initialized = 0 *********************
arch/mips/rtk_dmp/drivers/se.c, 768: offset = 0, se_devices = 9d8e0000
arch/mips/rtk_dmp/drivers/se.c, 778: offset = 0
arch/mips/rtk_dmp/drivers/se.c, 822: length = 20480
arch/mips/rtk_dmp/drivers/se.c, 823: offset = 495845376
arch/mips/rtk_dmp/drivers/se.c, 830: offset = 495845376
arch/mips/rtk_dmp/drivers/se.c, 768: offset = 98316, se_devices = 9d8e0000
arch/mips/rtk_dmp/drivers/se.c, 778: offset = 402702336
arch/mips/rtk_dmp/drivers/se.c, 822: length = 4096
arch/mips/rtk_dmp/drivers/se.c, 823: offset = 402702336
arch/mips/rtk_dmp/drivers/se.c, 830: offset = 402702336
fusion: unable to register major 247. Registered 245 instead
pli malloc order: 11
+++ ALLOC index: 59392 order: 11
zone: 8071f000 page: 808ef000(90800000) count: 2048
start remap DVR zone 90800000(808ef000) 2048...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 61440 order: 12
zone: 8071f000 page: 808ff000(91000000) count: 4096
start remap DVR zone 91000000(808ff000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 94208 order: 12
zone: 8071f000 page: 809ff000(99000000) count: 4096
start remap DVR zone 99000000(809ff000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 0 order: 12
zone: 8071f000 page: 8071f000(82000000) count: 4096
start remap DVR zone 82000000(8071f000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 4096 order: 12
zone: 8071f000 page: 8073f000(83000000) count: 4096
start remap DVR zone 83000000(8073f000) 4096...
total migrated: done: 0 fail: 0
[I2C0] i2c speed changed to 50 KHz
save exit: isCheckpointed 1
pli malloc order: 12
+++ ALLOC index: 65536 order: 12
zone: 8071f000 page: 8091f000(92000000) count: 4096
start remap DVR zone 92000000(8091f000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 10
+++ ALLOC index: 58368 order: 10
zone: 8071f000 page: 808e7000(90400000) count: 1024
start remap DVR zone 90400000(808e7000) 1024...
total migrated: done: 0 fail: 0
pli malloc order: 10
+++ ALLOC index: 91136 order: 10
zone: 8071f000 page: 809e7000(98400000) count: 1024
start remap DVR zone 98400000(809e7000) 1024...
total migrated: done: 12 fail: 0
pli malloc order: 3
+++ ALLOC index: 57608 order: 3
zone: 8071f000 page: 808e1100(90108000) count: 8
start remap DVR zone 90108000(808e1100) 8...
total migrated: done: 8 fail: 0
pli malloc order: 12
+++ ALLOC index: 69632 order: 12
zone: 8071f000 page: 8093f000(93000000) count: 4096
start remap DVR zone 93000000(8093f000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 8192 order: 12
zone: 8071f000 page: 8075f000(84000000) count: 4096
start remap DVR zone 84000000(8075f000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 12288 order: 12
zone: 8071f000 page: 8077f000(85000000) count: 4096
start remap DVR zone 85000000(8077f000) 4096...
total migrated: done: 0 fail: 0
pli malloc order: 12
+++ ALLOC index: 16384 order: 12
zone: 8071f000 page: 8079f000(86000000) count: 4096
start remap DVR zone 86000000(8079f000) 4096...
total migrated: done: 0 fail: 0

eth0: Set multicast.

eth0: Set multicast.
pli malloc order: 10
+++ ALLOC index: 92160 order: 10
zone: 8071f000 page: 809ef000(98800000) count: 1024
start remap DVR zone 98800000(809ef000) 1024...
total migrated: done: 159 fail: 0
pli malloc order: 6
+++ ALLOC index: 57664 order: 6
zone: 8071f000 page: 808e1800(90140000) count: 64
start remap DVR zone 90140000(808e1800) 64...
total migrated: done: 64 fail: 0
This is the current time: PowerUP_Done!!!
eth0: no IPv6 routers present

eth0: Set multicast.

eth0: Set multicast.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(860) 0xb8013808 = 0x4400a081
#@# cfyeh-debug USBPHY_Register_Setting(862) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(209) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(209) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(932)
#@#[cfyeh-debug] USBPHY_Register_Setting(934)
#@#[cfyeh-debug] USBPHY_Register_Setting(936)
#@# cfyeh-debug USBPHY_SetReg_Default_39(288) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ehci ehci: Rtk Dmp EHCI
ehci ehci: new USB bus registered, assigned bus number 1
ehci ehci: irq 2, io mem 0xb8013000
ehci ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(860) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_Register_Setting(862) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(209) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(209) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(932)
#@#[cfyeh-debug] USBPHY_Register_Setting(934)
#@#[cfyeh-debug] USBPHY_Register_Setting(936)
#@# cfyeh-debug USBPHY_SetReg_Default_39(288) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ohci ohci: Rtk Dmp OHCI
ohci ohci: new USB bus registered, assigned bus number 2
ohci ohci: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
#@# cfyeh-debug usb3_phy_setting_saturn(27) +++
#@# cfyeh-debug usb3_phy_setting_saturn(216) ---
xhci xhci: Rtk Dmp XHCI
xhci xhci: new USB bus registered, assigned bus number 3
xhci xhci: irq 2, io mem 0xb8020000
#@# cfyeh-debug xhci_irq(1752) 0x000002a0 0x002802a0
#@# cfyeh-debug handle_port_status(1101) 0x000002a0 0x002802a0
#@#[cfyeh-debug] handle_port_status(1129) NOT in U0
usb usb3: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
#@# cfyeh-debug xhci_hub_control(287) hack for usb3 portsc
#@# cfyeh-debug usb3_mac_setting_saturn(221) +++
#@# cfyeh-debug usb3_mac_setting_saturn(242) 16bit
#@# cfyeh-debug usb3_mac_setting_saturn(243) *(unsigned int volatile *)0xb8028200=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(244) *(unsigned int volatile *)0xb8028200=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(246) *(unsigned int volatile *)0xb8028200=0x2400
#@# cfyeh-debug usb3_mac_setting_saturn(257) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(259) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(263) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(264) 0xb8028108 = 0x02400008
#@# cfyeh-debug usb3_mac_setting_saturn(269) 0xb8028108 = 0x21010000
#@# cfyeh-debug usb3_mac_setting_saturn(272) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(273) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(278) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(283) disable usb mulit request
#@# cfyeh-debug usb3_mac_setting_saturn(284) *(unsigned int volatile *)0xb8013200=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(286) *(unsigned int volatile *)0xb8013200=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(291) GUSB3PIPECTL
#@# cfyeh-debug usb3_mac_setting_saturn(292) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(295) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(298) ---
pli malloc order: 8
+++ ALLOC index: 90368 order: 8
zone: 8071f000 page: 809e1000(98100000) count: 256
start remap DVR zone 98100000(809e1000) 256...
total migrated: done: 256 fail: 0
Realtek Bulid-In SATA Driver Rev:SATURN (2012-06-27 14:20)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA Package
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: HPA detected: current 7814037168, native 211925224963760
ata1.00: ATA-8: ST4000DM000-1F2168, CC52, max UDMA/133
ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST4000DM000-1F21 CC52 PQ: 0 ANSI: 5
#@#[cfyeh-debug] sd_probe(2285) sd_flag 1
#@#[cfyeh-debug] sd_probe(2351) sd_flag 0
#@#[cfyeh-debug] sd_probe_async(2190) sd_flag 1
#@#[cfyeh-debug] sd_revalidate_disk(2065) sd_flag 2
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
#@#[cfyeh-debug] sd_revalidate_disk(2124) sd_flag 1
#@#[cfyeh-debug] sd_revalidate_disk(2065) sd_flag 2
#@#[cfyeh-debug] sd_revalidate_disk(2124) sd_flag 1
sda: sda1 sda2
data[0] 0x0 signature[0] 0xbabeface
data[1] 0x0 signature[1] 0xdeadbeef
#@#[cfyeh-debug] sd_revalidate_disk(2065) sd_flag 2
#@#[cfyeh-debug] sd_revalidate_disk(2124) sd_flag 1
sd 0:0:0:0: [sda] Attached SCSI disk
#@#[cfyeh-debug] sd_probe_async(2252) sd_flag 0
ufsd: module license 'Commercial product' taints kernel.
ufsd: driver (8.6, Jul 25 2012 17:52:20, LBD=ON, delalloc, ioctl) loaded at c01f0000
NTFS (with native replay) support included
Hfs+/HfsX support included
For 'realtek_new_ic_2011-04-29'
ufsd: use builtin utf8 instead of kernel utf8
ufsd: use builtin utf8 instead of kernel utf8
ufsd: use builtin utf8 instead of kernel utf8
ufsd: use builtin utf8 instead of kernel utf8
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
fuse init (API version 7.13)
ufsd: sda1 without journal
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
save exit: isCheckpointed 1
Adding 130044k swap on /dev/sda2. Priority:-2 extents:1 across:130044k
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal

Есть мнения что в нём помирает?
IconBIT XDS1003D @MED1000X3D V4.0.2 > Yamaha RX-V675 + Vector HX300 + Jamo S416 HCS 3 > LG 42LX6500 @HDMI
cybernetik
 
Posts: 48
Joined: 09 May 2011, 10:42
Location: Россия, Стерлитамак

Return to Что-то не так

Who is online

Users browsing this forum: No registered users and 0 guests